All Installation Instructions for Estate Range TES356MS1

Heating element burned up

It was simple. Unscrewed to screws at the back of the oven. Slipped off the wire connectors then attached the wire connectors to the new part, put the screws back in and we were back in business.

Parts Used:

Oven Bake Element

Jerry D from Spring Valley, CA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

8 of 10 people found this instruction helpful.

Was this instruction helpful to you?

Control panel started beeping and locked-up.

I looked at the symbol codes located at the schematic diagram. Schematic diagram is located at the back of range. I followed step by step troubleshooting procedure on the diagram then ordered part. The control panel is easy to remove and install, just plug and play.

Parts Used:

Clock Control

marcelo from jacksonville, FL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

8 of 10 people found this instruction helpful.

Was this instruction helpful to you?

Original handle snapped off.

Removed the two screws holding the remaining pieces of the old handle - screwed in the new handle.

Parts Used:

Door Handle

Edmund F from Sewell, NJ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

7 of 8 people found this instruction helpful.

Was this instruction helpful to you?

Oven wasn't preheating to temperature

Repair of oven sensor easy to install; however, product did not resolve the problem. Returned new sensor and awaiting refund (2 weeks passed so far).

Parts Used:

Oven Sensor

Margaret from WALDORF, MD
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

8 of 11 people found this instruction helpful.

Was this instruction helpful to you?

The 8-inch burner only heated on high regardless of the temperature setting dialed in.

Unplugged stove from electrical outlet. Pulled temperature control dial off by hand. Remove screws to top back stove panel with Phillips screwdriver. Removed top stove back panel. Unscrewed broken infinity switch from stove. Unclipped wiring harness to broken switch by prying loose with flat head screw driver. Reclipped wiring harness to new switch. Screwed replacement switch back onto stove. Reattached back panel with screws.

Parts Used:

Infinite Switch - 8 Inch

Reginald from PLAINFIELD, IN
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

6 of 7 people found this instruction helpful.

Was this instruction helpful to you?

The burner would not shut off.

Pulled the dial off, unscrew two screws. Pull the switch out from the back. Disconnect the wires from the old switch and connect to the new switch one by one. Set the new switch in place. Sctew the two screws in to hold the switch in place. Push on the dial.

Parts Used:

Infinite Switch - 6 Inch

Richard from CONCORD, NH
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

6 of 8 people found this instruction helpful.

Was this instruction helpful to you?

Bottom drawer

It was easy to find the part. I ordered it on Sunday and it arrived Wednesday. A stress-free experience.

Parts Used:

Range Front Drawer Glide

Eric from Saint Michael, MN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

6 of 8 people found this instruction helpful.

Was this instruction helpful to you?

light bulb in water ice freezer door went bad

I didn't. Don't know how to get to light bulb to change it for this specific model

Parts Used:

Light Bulb - 40W

Carl from RIVERSIDE, CA
Difficulty Level:
Very Difficult
Total Repair Time:
More than 2 hours
Tools:
Screw drivers

8 of 14 people found this instruction helpful.

Was this instruction helpful to you?

Bake element was taking time to warm up

Wire connection was damaged, replaced end piece

Parts Used:

Oven Bake Element

Jean-Claude from Miami, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

5 of 6 people found this instruction helpful.

Was this instruction helpful to you?

dropped stove forward, handle broke and trim around it also broke.

Unsrewed what was left of the trim and oven handle. Just 4 screws total, then replaced the 2 screws of the trim and the 2 screws on handle.
Finished! Replacement parts fit perfect!!! Thanks a milliion!

Parts Used:

Range Door Handle

HERLIN from BOERNE, TX
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

5 of 6 people found this instruction helpful.

Was this instruction helpful to you?

The heating coil was no longer working.

My husband pulled the oven out and unscrewed the screws(in the back) the heating element came right out. He did everything on his own. The only thing he needed a little help with was for me to keep the heating coil flush to the back wall of the oven, while he screwed the new one in. It was a very quick job. The longest part was pulling the oven out to get behind it and sliding it back in.

Parts Used:

Oven Bake Element

Amanda from Midwest City, OK
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

5 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Oven Door Locked

Unplugged, took off back, removed old part, put on new part and connected. Replugged and it worked great.

Parts Used:

Door Latch

Grace from Beavercreek, OH
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

8 of 15 people found this instruction helpful.

Was this instruction helpful to you?

element went out on the stove

My wife did it! I got home one night and my wife had done it! That's how easy it was! Trust me, he is no handyman (woman) but she did it by herself. The part came fast, the price was better than any one else's

Parts Used:

Oven Bake Element

christopher from harrisburg, NC
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

5 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Electric contact connection melted, shorting out the range.

After unplugging electric service, loosened 3 Philips-head screws holding 3 wires from range and loosened 3 nuts holding wires from electric cord. Also removed 1 Philips-head screw holding grounding tab. Removed 2 Philips-head screws and removed the old block. Mounted new block with those screws and replaced and tightened all 6 wires.

Parts Used: