All Installation Instructions for Whirlpool Range SF372BEEW0

Broken oven handle

I removed the handle from the door, replaced the old one with the new one............. 1, 2, 3, just that easy. The replacement part arrived very quickly and the price could not be beat. Would I use them again...........Yes!

Parts Used:

Range Door Handle

CONSTANCE from LAWTON, OK
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Scews from old one didn't fit the new one.

I had to bring the new handle to the Hardware store and have them pick out screws that would work. The only problem is that I live 12 miles one way from the Hardware store. My advise is to order scews when ordering the handle.

Parts Used:

Range Door Handle

Raymond from Ashland, WI
Difficulty Level:
A Bit Difficult
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

When I originally purchased my stove, there was a large paper describing stove features. It was glued on and when I removed it, it left glue which I could not remove. I s hould have returned stove, but I didn't.

So, after several years of it bothering me, I decided to replace the oven panel. I ordered it one day and it arrived the very next day. It was an easy job to replace. Just remove two screws in back and replace the panel. While I was at it I also replaced the racks. Now I have a brand new oven,thanks to PartsSelect!

Parts Used:

Range Rack

Range Interior Bottom Oven Panel

Doris from Brookline, MA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Igniter in oven not working.

Pulled racks and covers out of oven. Moved stove away from wall. removed bolts holding igniter. Disconnected wiring harness. Reverse process to install new part.

Parts Used:

Range Round Carborundum Oven Igniter

Rachel S from Dallas, GA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

Was this instruction helpful to you?

light would not turn off

Lifted burner top remover 6 screws lifted plate removed switch and installed new switch, took about 20 mins to complete job

Parts Used:

Door Switch

Ramon from miami, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

gas oven wouldn't ignite

Removed the floor of the oven. Removed the flame difuser covering the burner. Igniter was in plain sight. Turned on the oven and saw that the element in the igniter did not glow. Removed the igniter. Found a replacement on this site. Ordered the replacement part, which I received 3 or 4 days later. Installed the new igniter. Turned on the oven. Saw the igniter element turn bright red. Replaced the difuser and the oven floor. Turned on the oven and bake 2 loaves of sour dough bread.

Parts Used:

Range Round Carborundum Oven Igniter

James from Alexandria, MN
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers

Was this instruction helpful to you?

Lower igniter wouldn't light oven didn't heat up

Ordered the part from you it came the next day didn't need to pay for upgraded shipping, nice. Followed the easy instructions on your site. It had all the right hardware it literally clipped on the wires and bingo worked like a champion. I've done this on many ovens it sure beats calling an appliance repairman and getting ripped off for a 15 minute job. Thanks.

Parts Used:

Range Round Carborundum Oven Igniter

Leonard from Hamilton, NJ
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers

Was this instruction helpful to you?

Broken drawer glide

Used a phillips head screwdriver to remove the single screw holding the part in place and put the new one on. Finding the part on this site was a breeze and it arrived quickly. A first rate experience all around.

Parts Used: