SF362BEGW7 Whirlpool Range - Instructions

The repair was easy. I had to remove the trim on the other side and the bottom. You slide the new trim on and screw in the bottom two screws.

After searching on the internet for a very long time, we were almost ready to order the screws "blind" (no picture) from Sears for almost $10.oo per screw. Then I stumbled onto this website and found exactly what I was looking for, with a detailed description AND a picture!! Not to mention a price that was two thirds less than Sears..for TWO screws. Now the oven door is secure and we are no longer on our search for the right screws.

switched out latch asy,rear

I removed the bottom srtip. Installed the new bottom strip, snapped in the side pieces. [The old ones screwed in.] Replaced the original handle. Ready to reinstall door.

This is a very simple repair. 1st shut off your gas. Disconnect your gas line from the gas shut off value to the Gas Safety Value(GSV/R)/Regulator. Disconnect the other 2 lines attached to the GSV/R. Remove the 4 mounting screws holding the GSV/V. Wiggle the GSV/R from its location. Carefully remove the 3 wires connected to the GSV/R. Install your new GSV/R in reverse order applying sealant to the threaded joints. test for leaks.............. your done!!!

Found that the two screws securing the bottom had rusted away allowing me to just lift the old bottom out. The new one fit in place exactly and really did not need the screws. Done in 2 minutes.

After removing the back of the stove, the old light socket was fairly easy to remove. The new socket slipped in place and the wires reattached and now the oven has a light again. A very simple process--especially for someone who's not an expert in repairing appliances.

First I removed the gas line from th wall. Second I removed to gas lines going from the regulator to the stove. The regulator then unscrewed from the stove itself and that was it. I reversed the process to install the regulator.

On the back of the range was a little plastic bag with the range document. In this document was instructions on how to check out the electronic controls, a drawing of the electrical wiring and a digram of the gas line part of the range. First I did the electronic part and it check fine. Following that the instruction was to check out the solenoid coils for the bake and broil valve. I believe the wires were blue, red and orange(it tells on the wiring diagram). It called for 216 ohms on each coil. When I unpluged the plug from the circuit board on the upper right backside of control panel I checked the resistance for the two coils. One side had 198 ohms and the other coil had 0 ohms. The instruction said that if either coil didn't measure 216 ohms or close to that value the valve would not work. So, I wrote down the Model number. Next I checked the gas valve for numbers, wrote down all that was on the valve because I didn't know which one was the part number for the valve. Went on line to the Whirlpool site, once in the Whirlpool site I found out they have a diagram of parts for different appliances, pulled up the model I was looking for, found the valve( under the valve part, the number was different than the one I had, but the information said it would fit the model of appliance I have) order the part. In a few days the part arrived. I turn the gas off, unplugged the electric. I removed the gas lines, had just a bit of a problem with the short gas line going to the burner for the oven, when the line was out I unplugged the control wires. Nake sure you write down how thw wires are on the valve before unplugging. There is an adaptor on the valve to the main gas line. You need to take this off and put on the new valve. This is where you need the pipe cement. Stay back from the end of the adaptor that goes into the valve one or two threads with the pipe cement. you do not want to get any inside of the valve. Put the adaptor on, tighten, plug in the control wires, replace the valve on the stove, connect the gas lines, put all the gas lines on before you tighten them. Turn on the gas. Check lines with soapy water for gas leaks. Plug in the electric, check it out. Don't forget to put the instruction back in their little plastic package and I also put a copy of the order I had for the new valve just in case I need it in the furture.

it took 2 people to do this job. we had to place a yard stick inside the door to keep it open because after we removed the 2 screws inside the door that held the handle on, the door would not stay open. after removing the handle we had to slide the glass down from the top and line it in the slots at the bottom and then we had to replace the handle back on top of the stove, lining up the slots and the side pieces. after that we screwed in the 2 screws and yea! we did it right. The glass is in and we managed to not break it!

remove the hinge stays they just clip in
remove the door. took out screw at bottom of door.
replaced trim.
replacing the door was a problem i didn't have pins to put in the spring loaded hinges so i used nails to hold hinge in position.
so make sure to open oven door first insert pins or nails in hinges then remove door. It would have took 10 min. to do.

Un-screwed 4 screws. Got part numbers off of the pieces. Put numbers in blank on web site and ordered the pieces. Parts cam in 4 days later and installed the pieces with my trusty screwdriver.

Remove 2 screws holding oven bottom in place.Lift out the plate and replace with new plate. The hardest part of the replacement was lining up the screw holes. By the way i have never received such great service from any internet company as Part Select. I ordered the part on a Monday and the part was at my home the NEXT DAY and installed that evening.

It was easy to find the part. I ordered it on Sunday and it arrived Wednesday. A stress-free experience.

Removed the old, broken drawer glide by removing the Phillips head screw. Then placed the new glide into place and fastened with the existing screw.

The rivet on the top of the bottom drawer front was missing. I lined up the drawer front with the supporting bracket behind it and inserted the rivet. All you have to do is tap the top of the pin in the center of the rivet to lock it in place. No rivet tool is needed. That should be explained in the parts listing because I bought the rivet tool before I realized I didn't need it.