S166-C Jenn-Air Wall Oven - Instructions

first removed the four screws that held the panel in place, tthen unscrewed the actual switch itself. I then pulled the wire, one at a time from the old switch and pluged the wire in to the new switch. upon completion I tested the oven selector switch and secured the switch in place, then replaced the panel. And I'm up and running again!

I watched a You Tube video,removed and dismantled the door, installed the new hinge. I forgot to remove the small pin which is similar to a rivet. When I tried to close the door it bent. Eventually, I remembered the shipping pin and pulled it out with any damage. Believe it or not, I had read about the shipping pin on customer comments on PartsSelect...Good luck, it is relatively easy!

Remove Vent Cover, Remove Old Filter, Replace With New Filter, Replace Vent Cover, Repair Complete

Easy job. Anybody can do it. This replacement is accessed from inside the oven.

1. Remove the two Phillips sheet metal screws that attach the backing element plate to the back wall of the stove.
2. Carefully and slowly pull out the element as far as you can to expose the two Faston connectors and wire.
3. While holding the heating wire exiting the baking element with the needle nose pliers, carefully remove each female Faston connector.
4. Installation of the new heating element is the reverse of above. I highly recommend that you use the needle nose pliers to hold the heating wire behind the male (spade) Faston connector while installing the female connector. This will prevent bending of the heating wire.
5. I also recommend turning on the new baking element to a high temperature for about 10 minutes with the door partially open to get rid of the new heating element odor before you bake any food.

Removed two nut screws (accessed with oven door open) with nutdriver, panel dropped out. Transferred wiring one-by-one to new switch, removed old switch with allen wrench, installed new switch, replaced panel. Done! However, the problem is not corrected and all other possibilities have been explored with no solution in site. Ideas needed.

lift out old filter, wash, put in new filter.

Opened oven door, took four screws out of the front control panel, removed the two screws holding the burner control switch to the front panel, removed the wires from the old switch one at a time and installed them on the new switch. secured the new switch to the front panel, put the four screws back into the front panel, and closed the oven door. Real easy repair.

Disconnected power from the stove. First I removed the down draft vent cover on stove top, then the two screws that held the switch plate in place, then used a wood chisel to pry the switch housing retaining washers off. Removed the remains of the old switch, Installed new switch, attached wires, and reinstalled switch plate. Placed vent cover on stove top and reconnected power.

Unscrew the two screws. Pull the element out a few inches. Unclip the wires by pulling them apart. When we did this the wires retracted back into the opening. It was difficult to reach them and pull them back out. Be sure to hold the wires or clip something on them to hold them out till you can attach the new element. Attach the new element wires and screw the plate back on.

Had to remove the glass top and the control panel and the panel bracket then use angled needle nosed pliers to compress the retainers then pull the switch from the inside of the oven

Removed the door removed 2 inner panels Installed and reassembled A Cake Walk NOTE be careful not to strip threads

Turned of electrical power. Loosen two screws that held the stove top part that held the switch. Disconnected the old switch by removing the two clamps that held it in place, made sure wires were connected correctly on the new switch and used the new clamps to attach the switch in place. Put everything back together and turned stove power back on. Everything worked as it should.

I tilted the unit back enough to scew the new legs into the threaded holes.

removing the vent grid on top, by lifting off, then taking out the filter screen. removed the 2 screws on the back of the switchplate, then slide it back. made a drawing of the color wires and which way the switch faces... (it matters)
I took off the the old press-nuts by just breaking them with needle nose pliers. removed the old switch, fitted the new one (paying attention to where the little prongs and big prongs were on the old switch. used the nut-driver to press on the new nuts that came with the switch, and hooked back up the wires, and put it back.

Removed old filter and replaced with new.