S136 - Instructions

Removed old filter and replaced with new.

My wife help take the door off. It was a little heavy . The door came apart very easy and went back the same way.We save over $300 by doing it our selfs.

Had to remove the glass top and the control panel and the panel bracket then use angled needle nosed pliers to compress the retainers then pull the switch from the inside of the oven

Removed the door removed 2 inner panels Installed and reassembled A Cake Walk NOTE be careful not to strip threads

Removing the oven door and several layers of metal to get to the seal, is a fairly easy process. Our door had three different fasteners, torx head screws to remove the door, a very small flat head screwdriver to remove the chrome door trim screws, and a nut driver to remove the inner panels and glass. The replacement seal is over-large and must be trimmed. Care should be taken when fitting the integrated wire. Bending at the corners only, makes assembly much easier. Reassembly is the reverse of diassembly. Care must be taken that the seal wire hasn't popped out of it's seat when the cover is installed. This is the most time-consuming and frustrating part of the repair. Patience is paramount to get a good fit. Because I had made an odd bend in it, about one inch of wire was not properly seated after the cover was seated and tightened down. I was able to gently squeeze it into the seat with a flat tip screwdriver without removing any screws. The final problem area is reinstalling the door. Although two people would be helpful to accomplish this Task, I was able to accomplish it with the aid of a three foot piece of 2x4. By wedging the piece of lumber behind both hinges, they were held open under tension to allow slipping the door on. Once partially installed, the 2x4 can be removed and the door seated. Hope this helps.

Turned of electrical power. Loosen two screws that held the stove top part that held the switch. Disconnected the old switch by removing the two clamps that held it in place, made sure wires were connected correctly on the new switch and used the new clamps to attach the switch in place. Put everything back together and turned stove power back on. Everything worked as it should.

easy enough. Before you start, draw a picture of where the wires go on the old switch ( or take a picture).

Un screwed the two screws in the downdraft section enough to release the unit that holds the surface burner controls.Then removed the control nob, unscrewed the two screws that holds the switch in the unit, removed the wires, making sure the color of the wires were placed on the same contact point. Put it back together and it worked
fine.Of course I did shut off the power before starting any of the above

I got online, found this site, very easily found the part. The pictures were a tremendous help to ensure accuracy. The parts were delivered within 3 days without special postage. Without a doubt, I will order from here again!

My daughter & I followed the instructions in your video and had fun repairing the door. The video showed exactly how to do the repair. I hope I don't need any appliance parts very soon but I will certainly pull up your web site if I do. Thanks for an excellent instruction video.

John - Hot Springs Village, AR

I raised the top of my Whirlpool Continuous Cleaning Canning Oven, then had to unscrew 3 screws and a lock nut, then raise top about 4 inches, so I could put my hand inside to unplug the wires to the switch, and push it through the hole in front, of oven. Then put the new switch through hole and plug in new switch. Then screw down top; and close lid. Part #866294

dissembled the burner, remove the broken blocpk and bad spade.rewiered and assembled the burner.

took out old one and after straightening out the significant bends in the metal frame holding the screen, that were caused by shipping the screen in too flimsy of a container, I installed this into the range.

lifted the top center panel off removed old filter installed new easy peesy

EXTREMELY simple - drop in. AND- the part cost less than half the price quoted by appliance vendor...2 years earlier !!! This site is a marvelous resource for parts one can install with minimal skill.