RVM1535DM2BB Hotpoint Microwave - Instructions

.Thank You Dan

Easy peasy - removed lens holder w/screw driver. Cleaned cover after removing damaged glass lens. Then unscrewed burnt out light bulbs. Installed new bulbs, slid in new light lens into holder and screwed back into bottom of microwave. Removed greasy filter and slid in new filter. Done!

unscrewed the screw, pried up metal tabs that hold in light lens. took out broken pieces, slid in new light lens re-secured tabs with fingers, screwed in the screw again.

Simply removed screw, pulled down light holder, unfoled the metal tabs, took out the broken pieces and replaced the glass lens and light bulb.

bought a replacement for it

Thanks to the person who previousley detailed how he drilled holes to access 2 hidden screws, that made my job so easy. Thank You.

Pulled it from the wall remove the front vent covers removed the control panel remove the door switches by a special screw driver bit which looks a star remove the electrical terminals pressed the plastic clip pulled the switch replaced it with new one then followed initial steps backward

Removed three screws from the top front cover and slide it out and following I removed the touch panel and the housing that holds the switches and replaced the bad one.

llation

-unplug
-remove top and front covers
-unplug wire connectors from heating assembly
-remove heating assembly from metal stand and push out of the way
-remove metal stand from dry
-pull out heating assembly
-install new one in reserve order

This particular model has 2 hooks that are separate.

1. Remove the plastic trim on the inside of the door. Use a spatula and be care not to break any of the snapping parts. It will come apart.
2. There will be a metal trim that needs to be removed in order to get to the "screw" or "rod" that holds the hook in place.
3. All around the metal trim, there are plastic snaps. Use a screw driver to release the snaps from the metal trim.
4. My metal trim did not want to fully be removed... I was able to release the side where the hooks were and the bottom snaps.
5. Use the needle nose pliers to remove the spring. I found it easier to remove the bottom part of the spring to free the hook.
6. I had to pull on the metal trim enough to get the rod out of the hook so the hook could be removed. Very difficult with one person, but I got it done.
7. Put the spring in the new hook before you install it.
8. Put the rod back in, then the hook, then through the right hole.
9. Attach the bottom of the spring back to the lower hole.
10. Snap the metal trim back onto the microwave door.
11. Snap the plastic trim back onto the door.
12. Move the hooks up and down and feel there is tension. This should probably be done after Step 9.
13. Breathe!!!!

Followed the video online.

The breaker was tripped but fuse was ok on testing. I kept the fuse for possible future repairs. To access door switches and fuse on this model JVM1850CF001, remove 2 phillips screws at top. Then slide the grill to the left (toward hinges) about 1 cm and it should easily come off forwardly. Remove phillips screw underneath grill attaching the main panel. Lift the panel 1 cm and it will easily come off forwardly - I let it hang by the electrical cords. Now you can see/discharge capacitor(s). Remove 2 star screws inside door to loosen/remove/access door switch frame. 3 switches are held in the frame by plastic tabs - one tab per switch. One is primary and 2 are secondary door switches. I removed each switch one at a time by lifting tab, pulled off the electrical connector and filed the male metal connection on each switch. I replaced the switch with a loose button (loose and didn't click as crisply compared to the other switches) with a new secondary door switch. It was the lower secondary switch. Worked like a charm after that.

Used chisel to remove inside cover. Unscrewed broken handle. (Didn’t expect that there was a second set of screws That were covered by metal frame of microwave. Had to cut the screw to remove. Then screwed the new handle back in. This handle only had 2 screws. Hope it holds as well as the 4 original screws. Part was kind of expensive, was not informed that there was an error in processing my shipment until I called. Then part showed up 2 days later.

Following the instructions from prior PartSelect folks for this part (thank you for great instructions), I removed the door from the microwave (first had to remove the fan vent grill above the door (2 Phillips screws), then I carefully removed the back plastic door frame using the thin puddy knife to carefully pop it off. Removed the first 2 screws on that are visible. Removed the inner door frame (was the most difficult part of the process to do without breaking the front panel frame) to expose the inner 2 screws. On our microwave, the front panel was also cracked, so I removed and replaced it (very simple), attached the new handle to the front panel with the inner screws (Phillips 2) and then popped the inner door back in, screwed in the last 2 screws and attached the back plastic door frame. Reattached the vent fan cover and the door. A bit more complicated than originally thought, but overall not bad. Charlie C