Quick Question!

Have you ever purchased from PartSelect.com before?

Models > RUD5750HB0 > Instructions

RUD5750HB0 Roper Dishwasher - Instructions

All installation instructions for RUD5750HB0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the RUD5750HB0
31-45 of 222
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Pump not working properly

  • Customer: James from Little River, TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
  • 8 of 9 people found this instruction helpful
I removed the inner nut holding the spray arm onto the pump. Turned the washer on it's back and removed the wire clip holding rear of the pump motor. Completely removed the pump housingand motor from the washer. Removed three(3) long screws holding the motor to the pump housing. Removed the dish from the housing and removed the old impeller and seals .
Cleaned the pump housing of calcium with lime-a-way. Reinstalled all new parts in reverse order as they order taken off. Cleaned inside of dishwasher with lime-a-away and general purpose cleaner. Reinstall pump housing and motor on washer in reverse order as they were taking off.
Reinstalled washer into cabinet and connected all hoses, drain lines and electrical wired. Turned washer on and watched it run throught a complete cycle. Worked just fine and no leaks. Parts were great.

Sincerely,
James

inlet valve cracked

  • Customer: Victoria from Clarksville, TN
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set, Wrench (Adjustable)
  • 12 of 21 people found this instruction helpful
I first removed the old part. when i removed the old part i could not get the conector piece off when i when to get a new one they told me i should replace the copper tubing with the more flexable tubing because the copper tubing can kink up and possibly break from the kinking. so i screwed the inlet valve on i put teflon tape on the all the threads of the conector piece screwed it into the new inlet valve with and adjustable wrench then i conected the new tubing, and tightend it down with the wrench i slowly turned the water back on to cheak for leaks. When i saw there were no leaks i turned the water on the rest of the way pushed the dishwasher back in and screwed it into place an i was done.

dishwasher leaked

  • Customer: SHANE from Dunkirk, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 8 of 10 people found this instruction helpful
first i picked out the old seal, use a screwdriver to get it started. Then I pushed the new one in after cleaning the seal channel. I fixed it during a commercial while watching my favorite tv show.

Old valve failed and started to leak.

  • Customer: Adam from Minneapolis, MN
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Wrench (Adjustable)
  • 8 of 11 people found this instruction helpful
Pulled off the old valve using a crescent wrench and screw driver. The replacement part was a 100% exact match. Slapped on the new valve and that baby was water tight. $50 on a new valve is a lot better than $500 for a new washer.

Partselect.com was so easy to use and find the right part. Way more helpful than whirlpool's site, but that's not surprising seeing as they have an "authorized repair technician" page.

Thanks Partselect.com!

dishwasher leaks from left side of door

  • Customer: Catherine from Holbrook, AZ
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 8 of 11 people found this instruction helpful
The old gasket came out easily, but had calcium deposits in area. I cleaned the area with vinegar and water and waited until it was completely dry. The new gasket went in very easily and looked great. I started the dishwasher and alas, it still leaks, so the problem was apparently not with the gasket, but some other area. But the gasket is nice and new. Any suggestions on next step0 in troubleshooting?

Dishwasher was not pumping out water

  • Customer: Shelley from Florence, SC
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 7 of 11 people found this instruction helpful
My husband did the repair. He sucked the water out with the wet/dry vac. Layed it over on the front and removed the pump motor and replaced it.

Replaced Door Panel Insert

  • Customer: Rosalba from Brooklyn, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 7 of 11 people found this instruction helpful
All I had to do was remove old door panel and retainer and I replaced with the new.
PartSelect were great. I highly recommend you guys.

Dish Washer was leaking badly

  • Customer: Michael from Germanton, NC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 6 of 9 people found this instruction helpful
Simply removed deflectors and gasket, replaced all , took all of 5 mins. workes great now.

the pin was broken

  • Customer: Jo-Anne from Columbia, SC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 7 of 12 people found this instruction helpful
but the pin in and add the pin though the 2 tabs close door on it open it up move the springs backwards to the door

cracked drain hose

  • Customer: Larry from Magnolia, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 7 of 12 people found this instruction helpful
removed two hose clamps and old hose. slid new hose on existing fittings on dishwasher drain and disposal and tightened hose clamps. Turned it on for test run.

door panels looked old/bad

  • Customer: Gail from Mayville, WI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 5 of 6 people found this instruction helpful
Washed the edges good and clean to remove old tape that was holding the old panels. Slid in the new ones and found that the retaining strip would not work without replacing the inner strip. I didn't want to order this $53 dollar plastic strip so I squeezed a couple of rubber pieces into the bottom of the side edges to hold the top panel. Placed the retaining strip in place and used a long strip of black duct tape at this bottom edge to hold it all. It works and the new panels make the dish washer look close to new,the black duct tape hardly shows. This works good for my 10+ year old dishwasher until it is replaced with one that has a better door design.

Front panel of dishwasher was dented

  • Customer: Luann from Springfield, MO
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 4 people found this instruction helpful
Pulled off the bottom trim, slid the old panel off and put the new panel on. Then popped back on the bottom trim.

the motor would not run.

  • Customer: gerald from new iberia,, LA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 4 of 4 people found this instruction helpful
i determined that the impeller was not free. ordered and installed an impeller kit which included a new bushing, which was the culprit. it was a fairly simple fix, needing only to remove the pump housing from the back of the motor. access to the impeller was by removing the screw-in, x shaped connection on the back side of the impeller housing. runs like new again. the fix was far less expensive than a new washer.

Bad Water Inlet Valve

  • Customer: Stephen from Park Ridge, NJ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench (Adjustable), Wrench set
  • 4 of 5 people found this instruction helpful
No Water supply to Dishwasher. Turned off main Supply valve under sink.First took off old Diswasher supply valve and repaired it by cleaning it and it worked for two weeks. I ordered the part, but then cancelled it and Partselect service was great and cancelled it immediately. After it went down after 2 weeks I re-ordered it and it came in 4 days.
To Take this part off I removed mounting scews with nut driver, disconeected electronic plug connector, removed the compression fitting from the water supply and removed the outlet hose..reversed all of the above to install.

water leak at pump house and drive motor shaft interface

  • Customer: tim from westfield, IN
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench set
  • 5 of 8 people found this instruction helpful
after removeing the mounting and trim screws,water lines and associated wiring, the unit slide easily from under the counter then the fun began.
After several years of being exposed to the terrible water here the parts had become covered in lyme scale.
to make a long story short, most of the parts came out with minor difficulty however the pump motor shaft had corroded and lodged into the pump impellar.
This made removal of the pump motor impossible with out cutting off the end of the impellar and driving the pump motor shaft out.
This is NOT something you want to do.
It seems the engineer who designed the pump motor had it's casing made of plastic.
Driving the pump motor shaft out of the impellar caused the back of the motor houseing to break thus rendering the pump motor useless.
Lesson: If it becomes necessary to cut off the impellar of in the pump housing you must completely split the impellar in two parts.
This I repeat is NOT something you want to do.
I recommend replaceing both motor and pump assembly as a unit.
All Instructions for the RUD5750HB0
31-45 of 222