Quick Question!

Have you ever purchased from PartSelect.com before?

Models > RUD5750HB0 > Instructions

RUD5750HB0 Roper Dishwasher - Instructions

All installation instructions for RUD5750HB0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the RUD5750HB0
16-30 of 222
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Latch broke on dishwasher

  • Customer: Steven from Edmond, OK
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 18 of 21 people found this instruction helpful
Look at the exploded parts diagram, that parts select provides on their website.

You have to take off the nine star pointed screws. So you need a special screwdriver or I had a socket set of them and I used a ratchet to make it easier. I think there are nine of them around the base of the door. Then remove the door and set it on the counter. Flip it over and there is a small plastic cover that has to be removed from the back of it, and it is easily removed by gently pulling on it.

Now comes the difficult part. There is a locking piece on it that holds the latch onto the door by interlocking with a piece on the back side of the door. I took a pair of wire snips and just cut the old interlocking piece off. This way I didn't have to try and slide the two interlocking pieces apart.

When you go to put the new piece on before you interlock them make sure they are put on right. Specifically the latch is pointing the right way to seal the detergent door. Otherwise it can be a pain to separate the interlocking pieces again. (which is why I cut it off the old one).

Then you're done. Just put it all back together.

it would turn off and on mid-cycle and finally quit completely

  • Customer: Nat from Raleigh, NC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 19 of 25 people found this instruction helpful
I turned off the circuit. I removed the interior side of the door and then the plastic covering over the electrical wires and switches (I counterbalanced the door with a couple of half gallon juice containers). I removed the wires attached to the switch on the door handle and the door handle itself. The handle and switch parts disassembled and I replaced the switches (part of kit). I cut off the singed wire and the other three beyond the damaged portion and stripped the wires and connected the extensions (part of kit). I attached the new wires to the switches and closed up the interior door. Lastly, I turned the circuit breaker back on. All was well!

door insert all scatched up

  • Customer: stephen from west islip, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 17 of 20 people found this instruction helpful
Took me a while to figure out that the bottom plastic strip is all that holds in the panel. Once it is removed , it pulls out easily When the new panel arrived,just slide it up into the top grooove, and push the bottom strip back into its groove. The front looks like new!

Dishwasher would not fill with water.

  • Customer: Robert from Waldoboro, ME
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Wrench (Adjustable)
  • 18 of 24 people found this instruction helpful
After doing some research in a repair book I decided to take a stab with a water inlet valve. With expedited shipping I ordered the part and within three days it was delivered. I installed it and the dishwasher seemed like it was trying to fill but still would not. After much cocnsternation I turned the water supply valve to the dishwasher a partial turn to close and I felt the water rush through the valve and the dishwasher then filled. Apparently the shut off valve must have been clogged plus it now leaked. I then replaced the shutoff valve and the copper pipe to the water inlet valve with flexible 3/8" tubing and the dishwasher thus far is running fine without leaks.

Detergent Cup does not open

  • Customer: stephen from venice, FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 22 of 37 people found this instruction helpful
Disconnect power supply to dishwasher. Open door and remove screws on inner door cover. Carefully remove inner cover while watching how inner parts are arranged. Found return spring on detergent cup linkage had rusted and broken causing detergent cup not to open. Installed new spring and re assembled inner cover. Rotated timer dial one full revolution to check operation of detergent cup. Worked like a charm. Re connect power supply to dishwasher and your good to go.

Dish Washer was leaking every once and a while. Shield came out and was deformed by heatinfg eliment and was found on the bottom of the unit.

  • Customer: Henry from Raleigh, NC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 16 of 22 people found this instruction helpful
The gasket was a breeze, with just pulling out the old one and slowly pushing in the new in the track with my fingers. The shield was a little harder since there was no instructions before me. It turns out that it fits in the inner door and is used as a baffel for the steam (another problem with leaking out the bottom). After removing the front cosmetic pannel you need to thread the shield inside on three tabs that hold it. It took a few times to orientate it properly but it snaps in when correct. After the front pannel was put on and the unit test operated, the washer no longer leaks. Highly recommend the parts and help from PartSelect and the others before me.

soap dispenser door/spring broken

  • Customer: KEVIN from PLAINFIELD, IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 23 of 45 people found this instruction helpful
removed old parts and re-installed new parts. The spring is a little hard to get to the right point without a jewelers screwdriver, after that everything worked fine.

Valve was leaking from plastic after water line change

  • Customer: Nathaniel from Chelsea, MA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Socket set
  • 15 of 24 people found this instruction helpful
Turned of water and unplugged the dishwasher.
Disconnected the incoming water line.
Drained on to the floor (have paper towels ready)
Disconnected the electrical feed wire.
Disconnected the rubber hose.
Unscrewed screw holding the fixture to the frame.
Took off the brass elbow from the old part.
Put pipedope around it and screwed into new part (carefully, so as to not crack plastic again).
Attached part back to frame.
Attached water lines.
Turned on water, plugged it in and ran dishwasher looking for leaks. No problem.

Latch broke on Dishwasher

  • Customer: Jim from St. Louis, MO
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Wrench (Adjustable), Wrench set
  • 15 of 25 people found this instruction helpful
Had to pull the dishwashwer out to replace the latch. Did this by unscrewing the 2 screws that hold the Dishwashwer to the under side of the counter. Dishwasher then pulled out easily. Then unscrewed to screws on the latch. The screws were accessed by pulling out the modling/strip around the dishwasher door. Also easy to replace the screws. But sliding it back in was a little harder. Had to shorten the front legs on the dishwashwer to get the back of the dishwasher to go back in. Then screw the front legs back out. Finally re-inserted the screws under the counter that attached the top of the Dishwasher to the counter top.

Dishwasher leaking water out the front door.

  • Customer: Robert from Pleasant Hill, MO
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 12 of 17 people found this instruction helpful
replaced the two water defiector's, I had changed the door seal and should have changed the defiectors at the same time. Save yourself some time and ordor both parts. This is a easy fix, anyone can do.

Water leak around motor shaft where it enters pump housing

  • Customer: Harvey from Port Tobacco, AL
  • Difficulty: Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
  • 13 of 20 people found this instruction helpful
After completely pulling out the dishwasher, I removed the rubber housing that connected to the housing assembly. I unscrewed the retaining ring which holds the impeller in place and then pulled the impeller off the shaft (which took quite a bit of force). I removed the seal seat ring and using the impeller and seal kit I replaced all the internal parts to the impeller system. (note: the impeller and seal kit acutally contained the seal-head and seal seat ring so I was able to return those two parts.) I put all of the disassembled parts back together.

Broken latch on dishwasher prevented operation

  • Customer: Michael from Patterson, CA
  • Difficulty: Very Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers
  • 11 of 14 people found this instruction helpful
Broken latch on dishwasher prevented operation
Door Latch Bolt PS11741367 replacement instruction.

There are no instructions known to mankind on this part, however I did manage said replacement through determination and beer. First I looked it up on the internet. All kind of results, except for the model I was working on. Called, very nice woman directed me to yet another YouTube presentation for another model. As this was no help, I chose to not call her back. Not her fault.
So, I did what every instruction for the other models called for, disconnect the power. Seemed like a good idea if everyone suggested it. After that, remove the inner door by removing the screws. At this point I would like to mention that I also ordered and paid for what I thought would be a set of inner door screws to replace the old and weathered ones. However, they sent me one screw.
Who in their right mind would pay $5.10 for ONE SCREW? Well, your looking right at him. I felt like I sold the family cow for a magic bean, but that’s another story.
So, without instructions, I compared the part I ordered with the one installed in the door. It matched up in many ways, with exception for the fact I would not budge from it’s position, wiggle yes, remove no. I stared at it for 10 minutes with no further progress. Something has to give. I decided to remove the cover of the electronics with the hopes and optimism of a child. It also did not want to be removed. Back to YouTube and the computer. Nothing. I stared at it for another 10 minutes. Drank a beer, and started to “horse” it off, somehow it became ajar, and was finally removed. Upon examination of the old door latch bolt, I noticed that it was attached to the electronic mass by 4 wires. I used my phone camera to record which went where with false hopes that the repair was in reach. It was either me or the dishwasher. At this point, good money was on the dishwasher.
After recording and removal of said wires, I took the entire door latch and whatever the other piece was, to a table for further study, and another beer. After said study and beer, I remembered looking at other parts, one came to mind, a small teflon rod. As I look upon the part I knew about, I noticed it was adhering to the alien part with wires by 2 small teflon rods. I found a small nail, and pushed them out of the part, and they final separated. I replaced the old part with the new one and then reversed all steps and procedures, attached wires, reattached electronic cover, screwed down the inner door, shut main door, and started a dish cycle. Works perfectly. You may ask about the expensive screw. I took it to a local jeweler, who found nothing remarkable about it. As there must be SOMETHING about it that makes it valuable, so I had it mounted and framed in a nice display case for friends and family to treasure for years to come. A real conversation piece, and one more thing to dust.

No water coming into dishwasher

  • Customer: Terry from Wharton, TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Wrench set
  • 9 of 9 people found this instruction helpful
I unscrewed the old water inlet valve from the frame of the dishwasher so that I could manuever my hand around to the backside where the rubber hose was connected. That was the easy part. I then had trouble holding the old valve while trying to unscrew the hot water copper tubing so I screwed it back on the frame. My dishwasher is close to 18 years old and I think that was part of the problem. After soaking in WD40, I finally got the valve out. Then I had to remove the "L" shaped connector to put on the new valve. Everything went back together a lot faster and it's like I have a new dishwasher again. By the way, I am a 53 year old female so that may be why it took me so long.

The dishtrack wheel came off the track and fell into the dishwasher and melted

  • Customer: Timothy from huntersville, NC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 10 of 13 people found this instruction helpful
I snapped on the new part onto the track. It was that easy! :) Thank goodness the part was available from Part Select!
T. Edwards

detergent door latch did not work

  • Customer: Judy from ESTES PARK, CO
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 11 of 16 people found this instruction helpful
I removed all the ( what my Husband called star screws ) star screws and removed the housing panel ( holds dish detergent cup and silverware basket ) I discovered everything accross the bottom was all gucked up with detergent soap accumulation. I took the part to the kitchen sink and used the sprayer hose on the part with hot water and it cleaned up beautifully, and the detergent latch then worked ( the spring that operates the latch was all gucked up with detergent accumulation ).
I am the wife and did all of this myself and it only took around 5-10 min. My Husband had to help me figure out the type of screws because they turned out to not be phillip screws, but as Hubby called them.."star screws".
Soooo, I did not need to use the Latch Kit I purchased, so will store it in my parts supply! :)
Happy repairs to you..
Judy Estes Park, CO
All Instructions for the RUD5750HB0
16-30 of 222