RGB790SEHDSA Hotpoint Range - Instructions

Took off broken part and replaced it with the new part by removing a Phillips head screw, the broken part, replace with new and reinstalling the same screw.

replaced lights in refrigirator and freezer

I took all of the oven racks out , then the bottom cover, over the element. I immediately saw the igniter coil was broken. I took the element out and disconnected the two wires. (I saw that the igniter coil was broken and knew that must be my problem. I got my manual out and found the part number and got on line and started shopping. I found part select, the price was fair and ordered it the same day. It was shipped out to me the same day I ordered it. Received it the next day and had the oven working again. Easy to order, great customer service, fast shipping department. Great job to all of you folks at Part Select. I would recommend PS to anyone that wants to save money and do it yourself. Go for it. tk middlebury IN.

1) Verified it was the broiler igniter that was damaged.
2) Removed the oven door, the lower pot storage drawer and the top range panel.
3) Turned off the gas supply in the top range area. Pulled the electrical plug-in out of the lower electrical panel (behind the lower drawer).
4) Used the nut driver to remove the two (2) 1/4" screws that held the igniter to the back wall of the oven. I later read in the Use & Care Guide that this is easier to do if the broiler burner cover is removed first.
5) I pulled the damaged igniter away from the back wall, expecting to expose wire connectors or splicing but was only able to get about 6" of the two (2) insulated wires before I could not pull them any further.
6) Therefore, I cut the wires and, without a proper wire stripper, cut about 3/8" of insulation away in order to make a splice between the wiring from the new igniter and the wiring coming out of the back of the oven. Big mistake ..... do not recommend this without using a proper wire stripper! I must have cut into the existing exposed oven wiring on one of the wires such that when I used the twist-on to make the splice, most of the wires (those wound together to form one wire) were damaged and broke away. Unfortuantely I did not find this out until everything was put back together and we (my wife and I) did the test. No results!
7) I took everything apart again and when I tried to pull the wiring back out from in behind the oven wall, one wire came out with the twist-on in tact and the other came out "with no wire attachment".
8) I now had to figure out how to get into the back of the oven to retrieve the "lost connecting wire". It is quite simple when you know what you are doing but no instructions (that I had) advised that the upper back light gauge metal panels could be easily removed to expose the wiring. This was eventually determined and the connections were both made again in a more positive manner.
9) We (my wife and I) put it all back together and this time it was fine ..... just had to be patient while the gas purged the air out of the broiler burner line.
10) Lessons learned: GE made it easy "once you knew how it could be done". I suspect GE feels that service type people should be doing these things but with a 120VAC (vs higher voltage electric type ovens) system why not provide the info for the "do-it-yourselfers" as well?

The bolts were below the base of the oven, and very difficult to remove and replace. The directions were not applicable to our unit. The good news was the igniter was correct, even though we had to adapt the bracket.

They turned out to be 1/4 inch hex head screws. Only after soaking with penetrating oil could we budge them. There must be a special tool to loosen them on the back side where there is no room to get a socket on them and since they are in the heated part of the oven they are almost welded in. We were successful, but could only get one screw back in. So never use your oven with the door left open as I did if you do not want to repeat what happened to me.

Removal old fashioned oven door handle took time after removing the oven door. New replacement handle was easy to install! Try to reinstall was long and finally got installed after 5 attempts due hinge on right side issue

Most trouble I had was removing the screws that were located under the bracket. I had to slip the oven door off first to give me more room. Very hard to get to these screws because of where they were located under the bracket. I had to twist and turn the old igniter to get to it. When finally removed, I replaced the old igniter with the new one using my own screws. I twisted the wires together, and replaced the baffles, the oven floor, and then the door. The oven fired up wonderfully! Thank you for your prompt service for getting me the part quickly and correctly.

First I took out the old Igniter and discovered the part I ordered did not come with any connectors, just bare wires. This is ok but I found myself searching the stores for the correct attatchments. It would be great if your web site gave the options to order these at the same time. This was my first repair of this kind so I had no idea what I was doing. I thought the part would arrive with what I needed to install it. The hardest part was getting the bolts off the under side of the Igniter. The space if very tight and at an angle that a regular took doesn't really fit. What took so long was taking the bolts off by hand. Im a single woman who likes to try to fix things first on my own. My 18 yr. old daughter was in there with me the whole time learning and finally it was her smaller fingers that were able to get the bolts into the new part. We only finger tightened the part because no tools would fit at the curved angle. I love your web site and the ease of finding the part I needed. Its the stove manufacture who made this project difficult by how they place the screws. I will use them for all my part needs in the future.

Removed the two screws that hold the oven bottom to expose the glow element. Also removed the lower draw to get to the connections. The job was only complicated by getting to the two bolts holding the glow plug to the oven frame. Getting them off and getting the new plug on was not easy with standard tools. There was not a lot of room to work the hex bolts and i wound up cutting the old unit out and attaching the bolts to the frame and cutting slots in the new unit so I could slot it in. That worked. The glow plug was the problem and the oven came right on.

the electrodes on this model have to be removed before you can raise cooktop, once cooktop is raised remove wire from burner bracket, use needle nose pliers to squeeze bottom of clip,remove &replace with new parts.

Ordered part from customer friendly Part Select and received the replacement part within a few days, and installed it promptly. Wife is happy and stopped grumbling about oven bottom unsightly defect! Small price to pay for a happy wife! Ernie

Two set screws in rear; removed easily with a screwdriver. Old oven floor lifted out easily; new oven floor dropped in just as easily; set screws re-installed. Done. Pleasantly surprised at how easy this went.

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

Took 5 minutes to repair easy peasy??