RF764*T2 Hotpoint Range - Instructions

This is a forty five year old oven. It was only four screws and it was done. The new part works like a champ! This save me from buying a $800.00 replacement. I removed the two 1/4 screws holding the element to the back of the oven and then took the flat head screws loose from the terminals on the old element. I then put everything back as it came out; took less than 5 minutes and the part arrived overnight! Thank you again!!

I have to tell you i got wrong partfirst it was my mistake I got on phone and the lady understood my problem and told me procedure of returning part I got the right partnext day. I watched the video on how to do the job,although O new how. The video was a wee bit off,from what was easy.The man doing the talk through repair showed detaching the connections and bending each one back s as to not go back inside there inclosure. The connectors were way short on this one .The only way to attach the element was to take off back cover and push them together back there. Took couple extra minutes ,but job don e Ps will be ordering something soon

I disconnected the 240 volt supply by removing the fuses from the fuse panel. Next I removed two screws that hold the element in place with a nutdriver. Then being careful not to short or ground the wires I pulled the element out 3 or 4 inches and turned the oven control to the on position and tested for voltage, line to line then each line to ground to be sure the correct fuses were pulled. Turned the controls back to off. Next I disconnected the wires using the same nutdriver and removed the old element.
I placed the new element in the oven, attached the wires using a screwdriver backing it up with pliers to hold the connector on the element, then slid the element into position and installed the two screws in the back of the oven, then reinstalled the fuses.
Partselect shipped the order right away. I ordered Thursday evening and received the element Monday morning using standard shipping. I wasn't able to reference the oven by part number (it is a 40 year old GE oven) but their pictures and 1" grid made it convenient to pick the correct part.
In the past I bought the main control circuitboard for my Kenmore dishwasher, a door light switch for my refigerator, a turntable motor for my GE microwave vent hood, and an element for a Maytag oven. Every time I have ordered parts they were in stock as indicated and shipped right away and were the right part.

Once I watched the video pertaining to the installation of the part, the job was very easy.

i removed the two screws that hold the element in place. i then pulled the element out and disconnected the two wires. then i connected the two wires and screwed the element back in place and now it works like new.

The replacement was easy: turned off breaker to range; unscrewed element from range top;opened ceramic terminal box; unscrewed element from range wires. Then I simply reversed the procedure, using the new parts. Easy to do and it only took about 10 minutes.

first i removed two screws pulled that hold the element in then pulled element out about 3 inche disconnected the two wires now hot meals thanks

Easy to do . Four screws,removed cover,removed switch. Installed switch,and cover. Time 1/2 hr.

A simple repair using your quality matched Part turned into a CONDOMINIUM CIRCUS (no fault due to the Part or PartSelect.Com.)

It was the 1st time in over 30 yrs. that we had to throw a Circuit Breaker Switch located outside in the communal large Metal Box between Condos. Not only did it NOT cut the power off our old GE Range - it turned off one neighbor's T.V. & another neighbor's Washer/Dryer Set.

As more Breakers were tried - MORE ANGRY NEIGHBORS ARRIVED ON THE PATIO. To complicate this - the next-door Condo just underwent extensive (read 3 Months) Renovation including REPLACING ALL WIRING..... and you might imagine the rest. No Breaker Switch numbers matched the Condo number written beside them in felt tip pen... it was complete chaos!
THANKS to PartSelect.Com our old G.E. is working again.

Yours truly,

William Rush,

it was hard to figure out the instructions from A switch to B switch to my switch. The first switch was no good the second one was good. prayer book didn't hurt.thank

Good directions

The original controls were different for the small burners and the large burners. The replacement part fits all. Before removing wires, pay attention to writing on new and old control and replace 1 at a time. The hardest part was being sure to cut the knob stem to the correct length. Control works well.

Replaced the old with the new following directions (mostly).

My oven is so old that the model # tag has been scrubbed blank. I search your site by Brand name and oven description. I found the pictured element in your listing and sized it up. Part arrived as promised. It was simple to install - power down oven via circuit breaker and remove 4 ea screws and removed defective element. Install new element and reattach via screws. Turn on circuit breaker and power up oven to test - all working fine.

I replaced the element. The new part arrived within 48 hours of being ordered. It worked. The part that sticks out the back of the oven with the connections was a little shorter on the new element which made it more difficult to put the wires on but it was not too difficult.