RF375PXWN2 Whirlpool Range - Instructions

Turned off power to range because I was scared. Unscrewed broiler element, pulled part forward and pulled off wires that were attached to the back, attached wires to new element, pushed it back in place, screwed it back on to oven. Cooked my bruchette!

1. Disconnected power from my oven.
2. Removed several screws that held the control block
3. Removed two screws that held the switch itself disconnected wires and removed switch
4. Reconnected all wires to new switch (no soldiering gun required)
5. Put control block back

Overall - very easy

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

This purchase was for replacement parts, not for repair. Installation was a simple matter of taking out the old and installing the new, which is extremely easy to do. One item was damaged; Parts Select was absolutely fantastic to deal with regarding replacement! One word of caution regarding the product - I mistakenly ordered Whirlpool drip pans which have an opening in the bottom, the Maytag pans don't. Initially I thought that it was a mistake by Parts Select; which wasn't the case. The pans fit perfectly so I kept them. If I reorder, I will be certain that I order the correct pans.

removed drawer below oven, reached under stove and unplugged from outlet, pulled stove out from between cabinets, removed the 8 screws with 5/16 nutdriver from back panel and removed the panel, removed knob from switch , measured length of stem on old switch and compared it to the new switch ( my old switch stems was shorter than the new one so using a pair of pliers I shortened stem per instructions that came with new switch, this was very easy to do ), removed the two screws holding switch to stove and removed the old switch, then I transfered one wire at a time from the old switch to the new one until I had all the wires connected to the new one, used same two screws holding old switch to the stove to mount the new switch to the stove and put knob from old switch onto the new one, installed back panel to stove using the same 8 screws, pushed stove back into place between the cabinets and plugged the stove into the outlet, put drawer back in place below oven door, reset clock and tried out the new switch, so far so good only time well tell if I fixed my problem because it only happens once in awhile

I turned off the breaker (I'm a little nervous even unplugging a 220 plug). I first removed the cover from the back of the stove to get to the wiring/socket. Removed the two wires from the leads - they just pull off by hand but use a needlenose pilers if it is stuck. One is larger so no need to try to remember which one goes where. I removed the glass cover and bulb from inside the oven. I read another post on this site that said there were clips that you had to press to get the old socket out which helped. That part was a little tricky as the insulation around the socket makes it hard to see and the opening is really tight. I finally found the clips and pressed one then got that side out enough to hold the clip back then pressed the other clip and I was able to push it right out. I did not have the strength to press both clips with enough pressure but if you do, that would probably be easier. From inside the oven, I pushed the new socket through the hole - there was a little notch in the opening that had to match up with the socket. I had to push pretty firmly until I felt both clips snap in place. Replaced the wires, turned on the power, screwed in the bulb and cover and I had light!

First I removed the oven door from the unit by removing the screws that are located approximately 6 inches from the bottom of the door. After the screws have been removed be aware and take caution when you pull the door up and away from the unit. The hinges are spring loaded and can casue injury. Once the door has been removed from the unit place it front side down on a soft rug or cloth to avoid any scatching. Remove the two philips head screws from the top of the door and the two philips head screws from the bottom of the door. carefully separate the interior steel panel from the exterior panel. Once the panels are separated you will see the first pane of glass. Remove the four nutscrews that hold it in place. Behind this pane of glass you will find the xterior pane of glass. remove it and install the new piece. Be sure to clean the glass before you install it. Replace the parts in reverse order and soon you will be cooking again.

I read several posts of this glass door replacement before ordering and was a little hesitant, but after looking at my stove door broken for a number of years I decided to make a move. I searched the site found item # PS337162 and ordered it. The posts didn't sound too complicated. The glass arrived in two days, the repair went amazingly fast 20 min max. The following worked well for us:

1) Removed screws from around door bottom, top and sides. DID NOT REMOVE SCREWS MIDWAY UP ON INSIDE OF THE DOOR, HOLDS THE SPRING LATCHES.

2) Removing the door is not necessary once the screws are out, the outside panel comes loose from the interior. Propped the exterior part of the door up to meet the top of the drawer on the bottom of the stove, the natural position of the door as if it were opened during normal cooking.

3) Once the exterior part is off, the interior is exposed, removed the screws which held # 4 glass along with brace in place (4 screws hexagon screws) before being able to remove the full size interior panel which holds the # 7 glass in place.

4) After removing the #4 glass, etc. the inner most part is exposed, the interior full size panel needs to be removed, took 4 screws (hexagon) loose and the panel pulled a loose freely.

5) When removing this panel be careful, the #7 glass drops freely once the panel is pulled back, there is also exposed insulation. Remove the exterior #7 glass and then pull the aluminum 1" spacer out to reach the inner most piece of #7 glass (this is the one I needed to replace) exposed inside oven. The cork seal appeared to be in good condition and did not need to be replaced.

6) Clean glass, and reassembled. Sounds like a lot but it is not, never removed the door from the hinges and replacement went very quickly. I wish I would have done this years ago.

I have had this stove since July 1994 and its been great, I have had no problems except the glass of which had nothing to do with the mfg.

I received my ordered in less than a week. It was great. The day I got them I remove the old burners and replaced them with the new ones. It took me about 3 minutes total. I was then able to cook my Christmas dinner with out any problems.

After removing the back of the stove, the old light socket was fairly easy to remove. The new socket slipped in place and the wires reattached and now the oven has a light again. A very simple process--especially for someone who's not an expert in repairing appliances.

After shutting off the power, I removed the door and oven racks. Then, by using a screwdriver, I removed each element one at a time and replaced with the new element. Each element pulled away from the back wall and was connected electrically by Sta-Kon connectors. All went well, and the unit was operational in about 30 minutes. I still have to remove the oven from the wall to replaced the two door springs.

Purchased 2 piece broiler pan from this site

Removed the two Philips head screws that attach the element to the back wall of the oven. Pulled off the two wire terminals from the spades on the back of the element. Pushed the two wire terminals onto the spades on the back of the new element. Noticed that one was not tight, so disconnected, squeezed down the wire terminal, and reconnected. Inserted the two screws that attach the element to the back wall of the oven. Element works fine.

Turn Off Breaker.

Removed oven racks....

Removed two screws holding element in place...

Disconnect spade lug connectors from old heating element.

Connected spade lug connectors to new heating element.

Reinstall 2 screws holding element.....

Replace oven racks.

Turn Breakers back On.

Done 10 Min. Install

Shut down breaker; remove stove back cover plate (8 screws); remove the control knob; remove knob screws (2); simply remove one wire at a time and replace the coresponding wire to the new control unit; remove the snap ring on the knob bar and snap off to fit the proper length; place the control unit in position and reinstall the 2 screws; reinstall the back panel; position stove and turn throw the stove breaker on; test the burner control.