All Installation Instructions for Whirlpool Range RF362LXTQ0

Burner went out

Two screws to remove glass top. 2 connectors to remove. Removed glass top and put it upside down. Remove 4 wires and 2 Phillips screws. Reverse steps.

Parts Used:

6" Surface Element, 1200 W

Ronald from DEFIANCE, OH
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Element had burned out, and the drawer glides were broken .

Replaced both .

Parts Used:

Oven Bake Element

Range Rear Drawer Glide

Allen from ASHLAND, PA
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Oven would not heat up.

Unplugged the range. Opened the oven door and took out the shelves. Took the right screw out, but had trouble getting the left one out do to the age of the range. Unhooked the two wires and took the element out. Put the new one in and hooked up the two wires. Attached the two screws and checked to see that the element laid flat and then tighten screws. Closed the door and plugged the range back in and turned the oven on and it worked perfect.

Parts Used:

Oven Bake Element

Johnie from PARKERSBURG, WV
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

range would not heat right

very easy watched the howto you gave

Parts Used:

Oven Sensor

bobby from HERSCHER, IL
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Electric burner element not working

Video said to remove screws and lift stove top off, remove contacts and ground. My stove top was hinged and required me to lift and pivot stovetop up. The burners were anchored to the stove base not the top. I secured the topso that it would not drop down and proceeded with repair

Parts Used:

6" Surface Element, 1200 W

Ronald from The Villages, FL
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

bake element out

use needle nose pliers to disconnect the element from the power supply. After disconnecting it was easy to repair.

Parts Used:

Oven Bake Element

Joyce from BALLWIN, MO
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

surface element not working

Ordered new element from PartSelect. It arrived shortly. It did not match the original. Guy at appliance store explained how I could connect the wires on the new one. It still did not fix the problem. A repair man tried for 2.5 hours to fix it with no success. Now I will return the replacement element in the return envelope provided.

Parts Used:

6" Surface Element, 1200 W

bruce from PORTLAND, OR
Difficulty Level:
Really Easy
Total Repair Time:
More than 2 hours
Tools:
Pliers, Screw drivers, Socket set

1 person found this instruction helpful.

Was this instruction helpful to you?

Oven Elementwas burnt into

Watched the video and did as shown

Parts Used:

Oven Bake Element

Fred from APACHE JCT, AZ
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

cooktop on the rt side would just keep getting hot

Removed the ifinite controlswitch and replaced it but i dont believe it is wired correctly. now it wont get hot until it is set on four or so. think i the way it is wired.

Parts Used:

Infinite Control Switch, 6"

Cooktop Cleaner

Michael from GRAND PRAIRIE, TX
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Removing an heating element that burnt into .

Unplugged oven , removed screws ,pulled wires out, removed old element , just hooked wires up , screws .make sure it sits level plugged in. Works great

Parts Used:

Oven Bake Element

Jenny from GREENFIELD, IN
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

element not working properly

Remove 2 screws inside oven holding element . Remove screws holding back panel. Plug wires (2) into new element.Install back panel . Done.

Parts Used:

Broil Element

PHILIP from NORTH PORT, FL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Oven Demon Possession

Our repair was extrodinarily easy. As my husband was taking out the old element and the oven was off, the element heated up and actually burned him. He readjusted it and it refused to heat again. We figured at that point that there must be a short, so we never even opened the box with the new element. A short time later we decided to use the top of the stove for soup and a small fire started in the oven. We turned off the braker at that point and ordered a new oven.

Parts Used:

Broil Element

Kevin from Greensboro, NC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

screw came off

very expensive to buy the part but just tighten the screw intot eh predefined place.

Parts Used:

Range Screw

Sandeep from EDINA, MN
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Light would not light

Pop old one out and new one in

Parts Used:

SOCKT-LITE

Frank from LEBANON, VA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

The side trim on the glass door needed to be replaced.

After we put the latch pins in, the door was easily lifted off. We placed the door on the table and unscrewed the trim pieces. The new trim pieces went into place after we cleaned the door. We slipped the door back on the oven and removed the hinge pins.

Parts Used: