REP309CD1 Kelvinator Range - Instructions

Working on 33 year old Kenmore stove (Harvest Gold color bought in 1977). Have replaced the element every 12 to 14 years, last in 1997. 3-5 FedEx delivery took only 1 day. I verified Selector dial and Temperature dial both set to off. I took out the 2 oven shelves and took off the oven door for easier access to back of oven. Open oven door slightly to 1st catch, slightly lift and pull door away from the oven to clear the 2 side hinges from the openings. I used 1/4 inch socket with ratchet to remove 1 screw on each side holding element to back wall of oven. Gently pulled element out and up slightly so connectors come through openings in back wall. 1 connector came out from wall 4 inches, the other just barely. I used needle nose pliers to pull connector off element with 4 inches of wire. The connector did not come off easily, it took some wiggling of the connector (not too hard because it is brittle). I pulled connector off element barely out from the wall and held the connector in the pliers (did not let go). Put old element on kitchen floor and put new element on oven floor. Attached connector wire to end of element so it didn't slip through back wall. Attached connector wire to other end of element. Lifted element slightly to push through back wall openings. Used 1/4 inch socket to re-attached both screws. I put oven door back on (reverse of taking off). I set Selector to Bake and Temperature to 300. I watched element heat up (nice solid color along entire length) and reach 300 temperature and cycle off. I opened oven door to force the thermostat to kick in the cycle again. I closed oven door to watch the element again. When the heating cycle finished, I turned the Selector & Temperature to off. When oven cooled off, I put the shelves in again.

Had to drill 2 new holes 1/4 lower in oven so new coil would bolt up evenly besides that it went easily.

Just removed nuts. Pulled out the element from the unit. Disconnected each end. Reconnected new element. Pushed piece back into insulated unit. Attached nuts. Done.

I had a friend come..He unpluged the old one and put the new one in when it arrived. All is well. Thank you for having the part that was needed. Now the over works super..
S.Bullock

They don't make appliances this easy to repair anymore. just as others say: screw out, unhook element ..hook new one to wires, screws back in.. you're DONE.. Thanks for great service and very quick delivery

I unhooked element from wall on inside. Only two screws to undo. I then took back of stove off and unhook speaker like connectors. It was very simple.

Very easy repair. First and very important step...shut off power to the oven! Then removed two small screws holding element to back of oven, gently pulled it and the wires connected to it toward me, disconnected the wires, connected the new element and reversed the process. However what I really appreciated about this was how easy it was to find the part on PartSelect.com. It was difficult to read the model number stamped on the plate at the front of the oven, and I got 1 letter and 1 digit wrong. But when I did the search, instead of just telling me "not found," it offered a list of model numbers that were close to what I'd entered, and the first one was correct. Very helpful! The online store is very well set up and easy to navigate.

Unplugged stove, use nutdriver, removed screws, pulled out old element, put in new one. Done. As prescribed. Excellent help as well as got part the next business day.

I used this site self diagnostic page and ordered the oven heating element as that was the item suggested for repairs. It was the correct part to fix my oven problem. I had my electrician visiting to install two light fixtures so I had him install the new heating element in the oven. Even with him going to the garage to turn the circuit breaker off for the range the installation took less than 5 minutes.
This site is the greatest!

Locating part on web site, ordering, receiving next day & installing was very very easy. Information provided on PART SELECT web site and that provided with part made this a very easy and cost effective repair. With service provided by PART SELECT there is no reason to pay for an expensive service call in addition to what a repair company would charge for the part.

(e.g. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...) I did have a problem with the wire connectors. they were a little over heated and loose, so I used pliers to ajust the connection.

***Make sure power is off the stove*** then remove oven racks.
Used 1/4 inch socket to remove 2 screws holding in the heating element, then pulled the element out a couple of inches to get at the wiring. Used pliers to unplug 2 spade clips.
Reversed procedure to install new element.

first i removed the two screws that hold the element in place. then pulled out about 3 inches
and disconnected the wires.installed in reverse
order.

Oven quit heating after less than 6 years. Checked with a volt-ohm meter and determined element was open. Ordered new element. Unit arrived in good time, replaced in about 15 minutes with no problems at all. Took longer to remove and replace oven door tha it did to install element.

Bake element went back in very easy. However still wouldn't work. Called repairman and computer chip was shorted out as well. Additional $250.00 later stove works.