RC5374W2 General Electric Range - Instructions

Removed two socket head screws form inside oven rear wall. Pulled element out and disconnected two screws attaching wiring. Replaced with new.

Just like your example said/turn the power off to the oven/remove the screws that hold the element in place and then I pulled th element out a little ways and disconnected the wires/reconnecting took a little longer only because it was hard to see/but I connected the two wires and put the screws back in and it worked. Saved me a lot of money/my husband wanted to get a new double oven

First I made sure the electricity was off. Then, I flipped the burner up, and loosened the screwon the hinge. This allowed the burner to extend onto the cook surface. After loosening the clips holding the ceramic insulator together, the wires to the element were exposed. The wires were then transferred to the new burner element from their corresponding position on the old one. The new ceramic insulator was affixed over the wire with clips, and the hinge reattached. The chrome ring was worked over the burner, and the burner reseated in its proper cook poistion. Testing confirmed the burner to now work as new.

Turned off power. Removed old broken one installed new one in minutes. Turned power on and tested it out. If this 60 something lady can do it, you can too.

Unplugged stove, removed front door, carefully removed two screws holding the cover plate of the element. Gently pulled the element out about 3-4 inches removed the two screw attaching the electrical wires to the element , making sure the wires did not pull back into the stove. Removed old element, attached new element to the electrical wires with the new screws received with the new element. Carefully pushed the wires and element back into place making sure the insulation was also in place. Re-attached the cover plate with the two screws I had removed. Plugged the stove back in and tested the element. Replaced the front door .... job complete!

Just wanted to add that the part came in two days, super mailing time, thanks!!

Flip the circuit breaker going to oven off, then used a 1/4 inch socket on the mounting flange bolts and the bolt head screws attaching the wires. Then used a flat head screwdriver to reattach the wires with the supplied screws and bolted the new element in place. Back to the circuit breaker flipped the switch and turned the oven on to test it, and now works fine. *be sure to remove the sticker before installation, use rubbing alcohol to remove any residue.*

lift eye slide in bowl and trim ring, put the eye back down,

Very easy repair. 2 hex head screws to take the heating element out. Then 2 more slot head screws for the wire connections. Perfect fit and operation of the new heating element.

First I read the already posted repair stories to give me confidence I could perform the repair.
Followed their steps -
Removed the two screws holding the plate to the oven.
Pulled out the element.
Removed the two screws holding the wires to the element.
Installed the new element by attaching the two screws (which were supplied) to the element.
Reinstalled the plate to the oven.
Tested it and it worked perfectly saving a costly service call.

It was so easy. Just removed the cover and then unscrewed the wires (keep track of which wires go to which side). Do teh reverse to reinstall

Repair was as easy as one, two three. Turned off the power and removed the two screws holding the element in place. Then pulled the element out approx. 3 inches and removed the two screws connecting the wires to the element.

From there I reversed the process and the repair was complete in less then 5 minutes, and I am not a electrician.

This was extremely easy to replace. When I told my mom I would replace it for her, she thought I was crazy. When she saw how easy it was, she finally understood. I had to remove the two screws holding the element in place. I pulled it out about 3 inches and unscrewed one screw for one wire. I didn't want to lose the wire, so I immediately connected the wire to the new element. I disconnected the second wire and attached it to the new bake element. Then attached the two screws putting the plate back up, securing the element. So easy! Just unscrewing and replacing 4 screws and I was done!! Took less than 10 minutes. I didn't have any real tools available, so I used a small adjustable wrench and it worked fine. The best part was it was so easy we were able to have a working oven in time for Thanksgiving!

Pulled out the bottom drawer of the stove and discovered the plug. So the plug was pulled from the wall socket.

Before this I had sprayed the screws with WD-40 and let it sit for 2 days.

Screws came out easily. Pulled out the old element and removed screws. Screwed on new element on both sides. Put in place and put old screws back.

Plugged stove back in. Turned on stove. Element came right on.

super easy - unpluged stove - unscrewed old element w/nutdriver from back of stove. unwired element - discarded. wired new element (2 wires). secured new element to back of stove. pluged stove back in. works great. Ordered part on Sunday, recieved it on Tuesday- VERY NICE SERVICE

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...I copy and pasted this from their example - it really is that easy - this is a simple repair.