RB800WJ5WW Hotpoint Range - Instructions

Unplug stove.
Remove rear panel of stove with a nut driver or socket. Remove knob from switch and use small screwdriver to remove screws on front panel switch. Remove and replace each wire contact one at a time to ensure correct wiring configuration. Replace screws on front panel to secure switch. Plug stove in and check that it works properly. Replace rear panel and move stove back in place.

I removed the 4 hex head screws holding the control panel , then the other 4 slotted screws. Disconnected all wires being careful to keep track of the color coding. Had a little trouble with the adhesive holding the face plate( I don't know why they even used it). Put the new panel in and reconnected it. Re set circuit breaker and tried the oven. It still wouldn't heat. it wasn't the control panel, but a burned out wire connecting the element in the back of the oven. Well, anyway I learned how to do the job and the the new panel activates better, so all was not lost.

every thing went great

Replaced old with new.

I unscrewed two screws inside the over over the element. Then I slowly pulled the element out and unplugged the two wires attached. Afterward I pushed the element back in place and screwed it back in and was done. Sure saved $550 I thought I might have to spend on a new oven,

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I then connected the wires to the new element and reinstalled the two screws. A brief test showed the element worked and that was it.

i dd not notice at first and started the self cleaner,,,i notice the self cleaner did not work,the screws had to be sprayed with dw30a couple of times and a pair of pliers to remove screws(no wrench set)after removing screws pulled the wires out to see and removed the connection to wires,,,replaced with new bake element and replaced the screws works fine,,,by the way i am a 64 years old grandmother

Removed two screws, and replaced element with a new one. Easy, works great.

First my son removed the two screws that held th element in place but first please tell everyone to turn off the breaker first. My son did not and he had gotten a shock from this and burned his hand. I think this is very important first. After cleaning up his hand he then replaced the element and tested it and it worked nicely.

Thank you for your prompt delivery and the correct part.

Sincerely
Kelly Didsbury

Removed the hexagon screws. pulled the unit out and wiggled the tabs loose disconnecting them. Installed the new unit-attaching the tabs making sure they were tight. Put the new unit through the opening in the back of the oven and reattached the hexagon screws. Back in business in about 10 minutes.

Followed the video and it was fast and quick.

slid the old ones out and slid the new ones in. done

Talked to parts select tech after ordering the control board. Tech advised me that he felt the range could be repaired without installing any parts. Advised me to contact manufacture tech support and explain the problem. I did to find that the child safety lock was on, probably from cleaning and touching too many buttons at once while whipping surface. Told me to hold down + and - at the same time for three seconds and it was fixed.
Parts select tech had told me don’t worry the parts are guaranteed so I called for a RMA and returned the parts for a refund. Thanks Parts Select, y’all are real professionals and that is greatly appreciated.
Thank you all.

Turne off power to range..pulled oven out..Took top back panel off with nut driver. 4screws .. Took picture of control board....removed bad control board with Phillips driver...4 screws....installed New board...removed 1 connection at a time and replaced in New board..Turned power on to test new board...check picture to make sure connections are correct...turn off power...put back panel back on...put range back in place...turn power back o n...done ..approximate time 15 to 20 minutes..

Pull the range out from the wall to access the rear of the unit. Turn off power to the range by unplugging from the wall or turning off the breaker.
Remove the large back cover from the oven portion of the range. Locate the two small wires and connector which is located between the two connections for the broiler heating element. Unplug the small connector.
Open the oven door and remove the screw that holds the temperature sensor in place between the broiler heating elements on the inside of the oven. Gently pull the sensor and the wire connector through the hole and discard.
Feed the new connector and wire through the hole from the inside of the oven. Attach the sensor to the oven wall with the screw.
Go to the back of the unit and make sure that no insulation has gotten into the oven space. Re-route the new wire being careful not to let it touch the contacts for the broiler heating element. Reconnect the wires to the connector and replace the back cover of the oven.
Plug in the range or turn on the circuit breaker. Slide the range back into place and re-level the unit. Test the oven to make sure the temperature is accurate and will maintain temperature.