All Installation Instructions for Hotpoint Range RB792DR1WW

THE FACE PLATE IS HARD TO GET OFF THE OLD CONTROL BOARD. USE A THIN KNIFE

THE INSTRUCTIONS THAT COME IN THE EMAIL ARE VERY GOOD. BE SURE TO TAKE A PICTURE OF THE WIRING.

Parts Used:

CONTROL OVEN TO9

Melvin from WEBSTER, TX
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers

1 person found this instruction helpful.

Was this instruction helpful to you?

Oven board went out

One wire at at time then used my razor blade to get front off stuck right back on

Parts Used:

CONTROL OVEN TO9

Jackie from TICKFAW, LA
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers

1 person found this instruction helpful.

Was this instruction helpful to you?

BASE OF BULB BROKE OFF & WELDED TO SOCKET

PULL RANGE OUT FROM WALL & ALSO REMOVED OVEN DOOR BY SLIDING UP. WORKING FROM INSIDE OVEN & ALSO BEHIND I REPLACED PART . ALWAYS " UNPLUG " RANGE BEFORE YOU START.

Parts Used:

RECEPTACLE PUSH-IN

NEIL from ROCKY POINT, NY
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers

1 person found this instruction helpful.

Was this instruction helpful to you?

Oven no longer working after running the self clean option. Only Stove top burners worked

I began by turning off the breaker in the panel.
Slide the oven out into the open area.
Removed 3 screws in order to remove rear top panel.
Took 2 pictures of the wiring location on the PCB
Removed all wiring going to the circuit board total of 8.
Removed 4 screws in order to remove bad PCB.
Remove faceplate from bad PCB (you will need to place this faceplate on the new PCB.

To Install.
Reverse steps above

Parts Used:

CONTROL OVEN TO9

Dominick from THORNWOOD, NY
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Bake button stopped registering

This was simple enough to repair for me, a relative novice. Just remember you need a nut driver to take the back panel off, take a photo of the existing board so you remember which wires go where, and you definitely need a hair dryer to heat up the sticker on the old board so you can remove it and put it on the new board.

Parts Used:

CONTROL OVEN TO9

Ryan from COHOES, NY
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers

1 person found this instruction helpful.

Was this instruction helpful to you?

Change bulb

Easy

Parts Used:

Light Bulb - 40W

Louis from LEAGUE CITY, TX
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver

3 of 8 people found this instruction helpful.

Was this instruction helpful to you?

Missing screw to range door handle

The part that was ordered based on the shamanic wasn't the part that was needed for the repair. It was to short. I took the other screw for the other side and that screw was an inch longer than the screw that was ordered thru your company. I then went too a jar that I placed extra screws, nuts and bolts which l keep in my garage . I found a same length screw but a different head and it works perfectly fine. When I ordered the part from your company most of the parts did not have a photo of the part on file, or a description like how long the part is. I still ordered it because it should fit the make and model number that was posted on the shamanic that was showed to me on line.

Parts Used:

SCREW 8-22 PL 1HX 71

Stanley from TRENTON, NJ
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Knob stem broke off.

Pulled stove out to access back panel. Unscrew broken switch/stem. Replaced each wire one at a time to make sure they went in right spot. Screw in new switch. Replaced back panel.

Parts Used:

Surface Burner Switch - 240V

DALE from FREMONT, NE
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers, Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Water dumped over in in my overhead microwave, which dripped down on, & shorted out a burner switch.

My husband had already removed the back plate form the stove and detached the wires from the old burner switch because it was keeping the burner on. He unscrewed the old switch and removed it. He then popped in the new switch, attached the wires to the correct contacts, and put the back plate back on. We plugged in the stove, and that burner works good as new.

Parts Used:

Range Surface Element Control Switch - 6 Inch - 1560 W

Deanna from Buckeye, AZ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

1 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Light burnt out.

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

Parts Used:

Light Bulb - 40W