All Installation Instructions for Hotpoint Range RB757BH4WH

front lift burner not working and surface light on with everything off

unplugged the range removed 4 screws from back top cover then took the knob off controller removed 2 screws from behind the knob removed 1 wirer at a time and placed it on the new controller in same order the wires came off put everything back to gather did not fix the problem .

Parts Used:

Range Surface Element Control Switch - 6 Inch - 1560 W

kevin from GAYLORD, MI
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Oven temp wouldn't regulate.

Followed the directions!

Parts Used:

CONTROL OVEN TO9

Ronald from Crumpler, NC
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Surface burner stopped working & light indicator remained on

It took my son very little time to install control switch. Using a screw driver he removed the back panel directly behind burner units & replaced the control switch. Very easy.

Parts Used:

Surface Burner Switch - 8 Inch - 2500W

Cynthia from BALDWINSVILLE, NY
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

lights blown out

replaced lights in refrigirator and freezer

Parts Used:

Light Bulb - 40W

Gerald from WINTERVILLE, GA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

6 of 14 people found this instruction helpful.

Was this instruction helpful to you?

Broken drawer glider

Took off broken part and replaced it with the new part by removing a Phillips head screw, the broken part, replace with new and reinstalling the same screw.

Parts Used:

Drawer Glider - Right Side

James from RANCHO MIRAGE, CA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

I'm Very Very Happy Was My First Order From This Part's Company ;

100% Pleased I Got & Installed All In A Few Minutes Your Company Is The Best Thank You Very Very Much ; Antonio

Parts Used:

Drip Bowl - 8 Inch

Drip Bowl - 6 Inch

SURFACE HEATING ELEMENT

Surface Burner Element - 8 Inch

ANTONIO from E STROUDSBURG, PA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

My electronic control board went out so I could not use my oven. My oven light blew as well.

I started with changing the bulb. I removed the small bracket that holds the glass cover over the bulb unscrewed the bulb and reversed to replace the bulb. To replace the control board I removed the top plate on the back of my stove took the small screw's out of the control panel and unplugged the wire's. Plugged the wire's into the right spots on the new control board and put it back together.

Parts Used:

CONTROL OVEN TO9

Light Bulb - 40W

Stella from PADUCAH, KY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Socket set

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Old Burner Chrome Ruined

Replaced

Parts Used:

Drip Bowl - 8 Inch

Drip Bowl - 6 Inch

RALPH from TROY, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Burner spontaneously cycled without knob activation

First I cut the circuit at the breaker, and then pulled the range from wall to access the access panel. This top panel was held with 4 screws and removable with a standard phillips head screwdriver.

I then removed the 5 wire-crimped fasteners from the defective surface burner switch. (I first labeled these wires to ensure correct placement to the new switch). There were an additional two screws behind the corresponding knob that needed to be removed in order to completely remove the old switch.

The new switch was installed in reverse order to the steps indicated above (two screws behind knob, 5 wire-crimped fasteners, 4 screws to panel). Range was pushed back into position and breaker turned on.

Parts Used:

Range Surface Element Control Switch - 6 Inch - 1560 W

Anil from Milpitas, CA
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Element blew hole in self then no power to burner.

Replaced burned element, did not fix no power problem. Ordered receptor replacement, replaced it, took less than 10 mminutes, but still no power to burned. Then ordered replacement switch, replacement too less than 10 minutes again and burner works fine.

Parts Used:

Range Surface Element Control Switch - 6 Inch - 1560 W

Melvin from Portland, TN
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers, Socket set

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

temperature sensor went

Took back panel off unplugged sensor and replugged in and worked like a charm!Sears wanted $400 and was going to 'overrepair"Got the 60 dollar part on here. UPS shipped to wrong address and customer service refunded my shipping and was excellent! would definetly use again!thanks

Parts Used:

Temperature Sensor Kit

Alex R from Randoff, NJ
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

1 person found this instruction helpful.

Was this instruction helpful to you?

Needed New Burner Bowls

Removed the old burner bowls, replacing them with the new ones.

Parts Used:

Drip Bowl - 8 Inch

Drip Bowl - 6 Inch

Carolyn from Garden City, ID
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Could not adjust heat on burner.

Followed directions given by previous customers problems which we found on the internet.

Parts Used:

Surface Burner Switch - 8 Inch - 2500W

Roy from Au Gres, MI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Replaced burner and it worked perfectly!

All I had to do was to plug the burner in and it worked.

Parts Used:

Surface Burner Terminal Block Kit

Surface Burner Element - 8 Inch

Marie from ROYSTON, GA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Oven would not heat up

I removed the rear lower cover. Disconnected the terminals from the heating element. Removed 2 screws from the heating element from inside the oven. Removed the heating element. Reinstalled everything in reverse order.

Parts Used: