All Installation Instructions for Hotpoint Range RB526C2AA

Rusted out burnner bolws

Remove old burnner bolws and install new ones

Parts Used:

Drip Bowl - 8 Inch

Drip Bowl - 6 Inch

charles from ft.pierce, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

no display

Turned off circuit breaker to stove, remove top panel and then the old control module and installed replacement. Power back on and top panel reinstalled. Easy!!! And Everything works like new!!!

Parts Used:

Oven Electronic Control Board

Rebecca from Las Vegas, NV
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Broken bake element

Very easy to install save several dollars

Parts Used:

Bake Element

Marcus from Lagrange, GA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

Was this instruction helpful to you?

needed to unstall "anti tilt" bracket on back of electric range to be code compliant for property..

Turned off circuit breaker, Then pulled out range, straight out and away from wall and cabinets. Layed braket on flooring and moved stove back in to make certain it aligned with range rear stands. Moved range back out, marked holes in braket, screwed in screws to anchor bracket. Pushed range back into placed against wall. Tried to |"tilt" range by pulling down on door after opened - range was held in place sre

Parts Used:

BRACKET ANTI-TIP Assembly

Greg from Ft. Washington, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Replaced my drip pans

The new drip pans are great. I had purchased generic ones locally that were supposed to be universal. The problem was that they did not fit right and the burner coils did not sit flat. The new drip pans fit well and look great too.

Parts Used:

Drip Bowl - 8 Inch

Drip Bowl - 6 Inch

Nancy from Mead, CO
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

I ord. drip pans for my Mother in another state

The drip pans arrived and she switched them out with the old ones Easy!

Parts Used:

Drip Bowl - 8 Inch

Drip Bowl - 6 Inch

Susan from Alpena, MI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

My drip bowls were rusted and corroded

I ordered new drip bowls and put them in place. They fit just fine.

Parts Used:

Drip Bowl - 8 Inch

Drip Bowl - 6 Inch

Glenda L from Lake Placid, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Old bake element burned out

Turned off circuit breaker, removed screws holding old element in with nut drivers, pulled out old element about 3-4" to reach terminals connected to back of element, removed spade lug terminals with needle nose pliers. Reconnected terminals to new element and screwed new element in place with nut drivers. Turned on circuit breaker and oven. New element works perfectly. Took about 8-10 minutes. Very easy to do.

Parts Used:

Bake Element

Thomas from Hamilton, VA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers

Was this instruction helpful to you?

Burned heating coil

Just pulled old coil out of the plug. Replaced drip bowl and inserted new coil in. No problem.

Parts Used:

Drip Bowl - 6 Inch

Surface Burner - 6-Inch

Maria T from Germantown, MD
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Old dishwasher rack and silverware rack

The whole process was very easy! I just got the model number and bought a new rack and silverware holder on,one. There was no assembly needed so I just popped them in and replaced the old ones! Very easy to do!

Parts Used:

Oven Rack

Anne Marie from Andover, MA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

dirty bowls

used my hands to remove heating element, then remove drip bowls, then install new bowls, then install heating elements, done!!!!!

Parts Used:

Drip Bowl - 8 Inch

Drip Bowl - 6 Inch

Richard from Bainbridge, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

GE Electric Range rear left burner quit coming on

Removed the back top cover with 1/4" nutdriver. Removed the burner terminal block with 1/4" nutdriver. Within 15 minutes had the terminal block kit removed and installed and in service.

Parts Used: