PSCS5RGXAFSS General Electric Refrigerator - Instructions

Removed the ice maker from the freezer. Unscrewed the outer cover/base of the ice maker. Unscrewed the long lever that opens the ice chute. This freed up the feeder coil enough to pull it out enough to replace the cup drive. Once I replaced the cup drive, I laid it back down into the ice maker bin, reattached all the screws and it worked! The old cup drive had a tine broken off which would not allow the feeder coil to turn. It seems like a weak part and I anticipate I may have to replace it again in a few years.

Removed tray, threw out ice , removed 3 screws used 2 screw drivers to seperate part & re installed

I searched YouTube for the problem and was quickly taken to several videos that detailed to required actions. This encouraged me to proceed, so I took the back cover off and found the water valve leaking. I then googled the make and model of the frig and found the part. The YouTube videos provided all of the details needed to determine the problem and replace the faulty part. Once the part arrived, I was able to install the new one in a few minutes. Operation returned to the water dispenser and the leak was gone. Total cost of the repair was $56 and took about 1.5 hours to remove the original part, order the replacement and install it when it came. Perfect!

Your instructions were "spot on"! Pried out broken switch with screwdriver-reinstalled new switch. Very easy! Ordered on line on a Wednesday new part arrived on following Saturday-Great service and will definately use again. Highly recommend PartSelect!

Took out ice tray and then slid motor out of right side bracket and sat on shelf. Removed the 3 screws holding up left side bucket glide first. Make sure you have correct size socket for the 3 screws on bucket glide. Works best with a screwdriver type socket tool. I then removed broken plastic piece from motor (screw in motor is different size than the ones for left side bucket glide). I put in new left side bucket glide (rear back screw a little bit of a challenge but it can be done) and then slid motor back into right side bracket and fastened motor to new plastic piece that sticks out from left side bucket glide. Put back in ice tray and good to go!

Ordered the icemaker replacement. unplugged the unit, followed the simple instructions and got it done in less than 30 minutes. It did take a LONG time to start making ice. But it's working now.

Removed ice bucket and observed the plastic drive bushing for the auger had the drive dog broken off. I removed the four screws on outer shell for the ice bucket, removed it and found the auger had key stoned a hole in the ice tray housing. At that point I decided to replace the ice bucket and auger assy. The new one works fine.

I removed the ice from the tray, took out the four screws from the tray, pulled up the metal spiral took out the old drive cup, replaced with the new one, replaced the screws and put the tray back in the freezer. A piece of cake. Thanks for your prompt service and the reviews on how to replace.

Removed tension spring, removed old lever, installed spring on lever, inserted lever in hole, re-attached spring to hook under front of refrigerator.

several times I had to remove the ice maker door solenoid due to it sticking. I ordered a new one from parts select. Problem solved!!!

I removed the 4 screws from the cradel then I wedged the tabs open on the unit and removed the main operating mechanism .Ithen removed the broken parts and reassembled the mechanism I put the unit back together in
reverse order. It works just fine.

Procedure for Replacing the Ice Chute Plate
1. Turn off the power.
2. Snap off the outside trim ring. Use a plastic screwdriver to avoid scratching the cabinet.
3. Locate the three small holes below the control panel facing, just above ice chute. The center hole is not used. With a small, blunt, object (wire – blunted nail) that is slightly smaller than the holes, push up rather firmly up through the outer holes to release front control panel.
4. Remove the three wire connectors from printed circuit board. Firmly pull/pry them straight out of retaining clip. Use caution: Excessive force will break clips.
5. Release the secondary panel by removing four screws (one in each corner).
6. Remove the flap assembly.
7. Clean all accessible areas with 1/10 bleach water to sanitize. Rinse the cleaned area with clear water and thoroughly dry everything before re-assembling the panel.
8. Install the new flap assembly.
9. Re-installed everything in the reverse order and check the functionality.
10. Order a spare ice chute flapper to be ready for the next event.

I removed the outer plate by sticking a very small screwdriver in the small holes at the bottom of the plate and pulling the plate toward me.
I then removed the 4 screws from the internal plate and pulled the plate toward me.
Then I romoved the 3 screws holding the old solenoid and unplugged it.
Next I put the new solenoid in place and replaced the three screws.
Finally I plugged in the solenoid and replaced the internal and external plates.

Since I didnot know if the issue was with the “ice maker” or the “ water valve” I decided to replace both components. I replaced the ice cube maker first, which required removing the attached bracket from the old unit on to the new unit. One screw attached and than I leveled the unit( total time was about 1 hr) a little learning curve. Next I replaced the “water valve” (total time 20 min.) I replaced each hose one at a time and the same for the electric connectors. Total parts arrived in about 1 week and cost a little over $255.00. I called the appliance store and they quoted me an estimate of over $700 ++++.
Everything works perfectly!! BELIEVE in yourself.

Watched a parts.com video on how to change defrost thermostat and followed the instructions