PLHS239ZDB2 Frigidaire Refrigerator - Instructions

Remove the bottom freezer drawer. Remove back metal evaporator panel. Wire in new defrost terminationT-stat. Reassemble evap panel. Good to go.

My son and I did it together. I was able to copy and paste the parts diagram on your website and we were able to go step by step following that diagram.We first shut the power to the refrigerator.We then removed the tray and the pad with buttons on the exterior of the fridge. We then unsnapped the electrical plug and were able to tilt the casing that holds the actuator. We removed the old one, and snapped the new one into place.We plugged it in and then proceeded to replace everything. Voila....we now have water again, all for the price of the part...Great!!!

Not too bad, remove the water and ice bezel (3 philips screws) then remove the dispenser unit another 3-4 philips screws. Remove water line from dispenser unit (remember this as the water tube re-insertion is the complicated part) I did not remove anything other then components listed above. Seals and inner door stay intact. Replaceing the actuator and arm was easy. two small philips will free the actuator and arm. Disconnect the two wire harness (black and red) NOTE- there are two sets of black and red wire harnesses that plug in next to each other. One is for the ice dispenser and the other for the water. putting it back together is as easy as taking it apart. However the water line has no play, no slack at all so when reinserting it, the space between the dispenser unit and the door itself is limited. Put the tip of the hose down into the hole you removed it from, hold the dispenser still and use a pair of long needle nose pliers to push (feed) the hose down into the hole. Make sure it comes out the other side by about 1/4 inch to insure it is in and stable. reinstall the unit and bezel. Most of my time was spent feeding the short water tube back in place. You will see just how much room there is between the dispenser and the door before you pull the water tube from the unit. In this case you can judge if it will be too complicated for you before you go any further.

Unscrewed the lower back cardboard panel and removed it. Unplugged refrigerator. Reached in and took the metal piece off that keeps the starter from coming off. Pulled the starter off the compressor. Unplugged the starter from the power line. Replaced starter. Hooked power line back on. Hooked starter to the compressor. Put the metal piece back on to hold in place. Plugged refrigerator back in. Put back panel back on.

It was simple. I loosened the two screws holding the ice maker unit. Then disconnected the wire harness. Plug in the new ice maker and tighten down the two screws. Held reset button for 15 sec. Done! took ten min. I had a full try of ice the next day!

I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.

Replaced the Triple Water Valve

Looked at video on how to remove and reinstall support and followed the instruct ions

First I obtained the manual to the refrigerator. I identified the screws to be removed. I turned off the water then unplugged the water lines. I then replaced the Water Filter Base and reassemble the parts. Within minutes of turning on the water, water and ice making had returned. I was a hero for saving the family $200 in parts and labor.

Support studs have an expansion fitting - center post has to be pushed through to allow expansion joint to collapse for removal. After installation, this post can be pushed in or pulled out to secure the stud and be the proper length to hold the bins.

None of this was obvious - an online tip from another member was invaluable.

Remove shelves and rear panels to get to motor. Motor is held in place on shroud by simple strap. Remove fan blade, then un hook strap, remove and save rubber spacers on old motor to reuse to remount new motor. New motor Mew motor has wiring harness that is universal. Cut out the three wires that go to the new motor leaving long as possible, cut wires from old motor as long as possible, strip ends of all wires 1/2 inch, connect wires by color,slip into provided wire connectors and crimp. Pull on wires to insure connection. Tie wires together so they don't touch the coils. Plug in and check operation. If all is working unplug and replace all covers and shelves. Plug back in and it will take few hours to reach operating temperature. Video of side by side repair shows easy removal of panels and motor.

I had to remove the face cover to gain access to the ribbon harness, also had to remove the push pads The ribbon is a delicate item so care had to be taken not to bend the ends. The ribbon can fit either side so getting it in place to make contact was kind of tricky. After the ribbon was in, it just a matter of putting things back together. Dispenser is fixed at a minimum cost, ribbon was shipped within 2 days which was great. Thanks to Part Select for easy to find on the net, had a complete diagram of the refrigerator ice/water dispenser so finding the parts needed was simple. Doug

I removed the filter bypass from the box. I opened the refrigerator door. I put the filter bypass in the space where the filter was located. I closed the refrigerator door. I opened the freezer door. I turned on the ice maker. It worked.

It was very simple-it is just an insert glass shelf above the vegetable drawers. But, it was fairly easy to identify on your website and delivered in about two days.

I followed the past suggestions and I opened the parts list to understand what was where. Caution when removing the face plate. The flat white connector pulls out easierly. It can be plugged back in after. I have big hands so it was hard to connect the water back to the unit. Other wise it went ok.
OH , make sure to unplug the refrigirator. I touch the control board and got snapped.