PLEF489CCF Frigidaire Range - Instructions

Watching the video showed an easy, unscrew and screw back on process while connecting the wires back. It was really that simple. Once it was complete (not even 10mins), plugged it back in, and its been working great since.

replaced it

Really a no brainer, but I do have to say that PartSelect customer service is excellent. My part was located and on it's way within a day and arrived a couple of days later.

After trying to unscrew a plate on the side, I found that would NOT work at all, the side panel of the stove was behind it. I found a tab that cut-out on 3 sides just above the location of the recepticle, and simply bent that tab out, pulled out the old recepticle, slid in the new recipticle, and put in the screws and then bent back the tab. It was sooo easy once I found that. I repeated in on the other side.

Removed both sides, removed ceramic glass surface, disconnected surface wiring.
Replaced Small oven Latch, replaced both sides and storage drawer.
reconnected wiring, replaced control panel end covers

Took 3 panels off to get to the electric block. Replaced electrical block and put it back together. Still no change.

Easy as 1-2-3

First. shut off the power!!! Remove the two screws holding the coil. Next- slightly pull remaining wire to access the plugs. Unplug the wires, remove old coil, replace and plug in the new... Replace two screws.... Turn power on and....... Start cooking! EASY!

Removed 2 screws holding old temperature sensor inside the oven and gently pulled out the wire till the connector came through the hole. Disconnected old probe and attached new one. Fished the wire back in the hole and replaced the two screws. Then followed the operating instructions for calibrating the oven. Ended up setting it +5 degrees. So far, works great.

Gasket has pins that line up with tiny holes around the perimeter of door. Just pull the old gasket off, and snap new one ( with pins) in . Used the butter knife to push ends of gasket in hole at bottom of door. Took about 2 minutes to complete and looks AWESOME! simple. simple, simple! This company ships immediately and the product is described properly. I would buy from this company again!

Started with three screws on outer edge of door, which separated inner and outer door parts exposing the first set of screws on first piece of glass. There are four panes including inner and outer with two between. Keep track of the screws, be careful removing and replacing glass panes (i put mat down to rest glass on)and with nothing more than a screwdriver and windex to remove fingerprints etc from replaced glass, it was a breeze. Good luck! - FK, Bahamas

The repair went relatively easy. I even cleaned all the layers of parts when they were removed from the glass panel. I have to thank the excellent customer service and super fast delivery. Overall a quite easy task and $$ saving as well!

This repair was easy, but I would not have even tried if I hadn't read the tips from other DIYers - thanks! The website questions and schematic along with some common sense testing isolated the problem with the oven only heating up to 250 degrees. Since the broiler (upper element) worked ok, that made it likely that the temperature sensor was not the problem. That made almost certain that the bake (cooking) element was the problem. So, I ordered the part, which was delivered quickly. Early on the morning of the scheduled delivery date, I turned off the oven power at the fuse box and pulled the oven away from the wall. There were only 4 screws to remove in order to take off the rear panel. The bake element was attached to two slide-on connectors, one of which looked charred and partially disconnected. I cleaned the charred connector, reattached it to the bake element, turned the power back on, and then turned the oven on. The charred connection glowed, so I immediately turned off the oven and the power. I disconnected the bad connector, cut it off from the wire, and stripped the wire to prepare for a new connector, which cost 30 cents at the hardware store. The bake element connection was cleaned, and then the new connector was attached. The power was turned back on, and then the oven was turned on, and it heated perfectly. After confirming several heatings over several hours, the rear panel was reattached, and the oven was pushed back to the wall. This expensive 40" dual fuel oven had been purchased new and used for 3 years by the prior owners of our home. The oven's computer brain died when the oven was 7 years old - the repair cost us $500 for professional labor, parts, and materials. I don't know if I could have done that repair, but I had no intention of shelling that much again, which is why I tried this bake element repair myself. The oven is now 11 years old, and the most likely part to fail is the original bake element. So, we may keep the new part as insurance with the hope of making a fast, easy, inexpensive repair when the original bake element eventually fails.

Took screws loose, unplugged old one plugged in new one put screws back

Figured out that light and door switch started the convection fan on when door is closed. Found the switch defective. Found exploded view online of switch in oven. Had to figure out that the range top needed to be removed to access the switch from inside the top part of oven. Unscrewed at least (6) screws to free up the range top. Squeezed the inside switch clips to allow switch to be pulled out from outside of oven. Disconnected electrical receptacle and plugged into new switch. Pushed in new switch til it snapped into place. Reinstalled range top.