PFSF5NFCABB General Electric Refrigerator - Instructions

Took old one out with my fingers. Put new one in with my fingers.

Removed ice bucket, and unplugged ice maker. Removed light cover. Removed ice maker. Pulled fan blades straight up and removed. Pushed new blades on to motor shaft. Fairly easy .

WE (WIFE) took out the old parts an replaced with new one ..Be careful to get the placement of the Grommet or they "POP" out on you. fast ship on the parts too.

This was so easy I think it took me 2 minutes. I am not very mechanically inclined but that didn't matter! Works perfect thank you!

Replaced Temperature Sensor and now it is getting cold.

The best instructions were several YouTube videos for replacing icemakers on GE french door bottom freezer refrigerators, but none fully described the process. The following difficulties were encountered: (1) Instructions for removing the freezer door showed three screws on each side that needed to be removed; in fact, there was only one screw on each side. It was smaller than the three depicted screws and its location was not exactly as shown in the videos. (2) None of the instructions adequately described the process for removing the mounting plate from the nonfunctioning icemaker so it could be attached to the replacement unit. The key was to forcibly pry open the cover over a screw that then needed to be loosened with a screw driver. It seemed that I risked breaking the unit when I tried to slide the tab, but it eventually moved and revealed the screw that was holding the original mounting plate in place. (3) Replacing the freezer door required lining up some metal studs with slots in the undercarriage; you need to get down on the floor to examine how this fits back together. (It might help to take some photos before removing the freezer door.) (4) Replacing the upper drawer was perhaps the trickiest. My first effort resulted in having the rod with gear pinions on each end pop out because some of the tabs holding the gear pinions on each end broke. That meant that I had to order two replacement gear pinions (left and right are identical). Then, as with the freezer door, it was necessary fo slide metal studs on each side into a vertical slot leading to a horizontal slot in order to seat the upper drawer properly. So the whole process took a few weeks; actual work time was perhaps 3-4 hours. This could have been shortened significantly had I taken photos as I disassembled everything and if the procedure for moving the mounting plate had been clearer (or even existing). All in all, though, this is a doable DIY project.

Remove the top cover above the door by lifting it slightly and pulling forward. I used a mirror to make sure that there was nothing in the way of accessing the switch from above. I used a blade screwdriver to press against the switch retainer on the topside, while GENTLY prying from below with another blade screwdriver to get the switch dislodged. Once the retainer was past the opening, I wiggled the switch downward and then rotated it to the left when the rounded top right edge of the switch was visible. This allowed the wiring to the connector to pass thru the hole. I pushed the wiring from the top and pulled from below to get the connector below the opening for the switch. I then unplugged the switch, plugged in the new switch and reversed the removal process feeding the connector thru first then rotating the switch to the right to get the rounded edge of the switch thru the opening, then pressed the switch up into the opening until it snapped into place. Total time less than 10 minutes.

I watched a you tube video for 2 minutes & did the replacement in1 minute.

I followed your video and completely dismantled the refrigerator evaporator motor, fan, brackets, and grommet, I completely cleaned the refrigerator including the cooling coils. I then ordered the evaporator motor ,fan, grommets, lid bumper, and brackets. The order would take a week to arrive. In the meantime I cleaned and reassembled all the old parts, waiting for the new ones to come. Guess what! The refrigerator was quiet as a mouse. I really did not need the new parts, but I kept them anyway just for good luck. Not bad for a refrigerator that's twenty four years old.

Easy

We didn't think the dispenser problem was related to the filter - we were wrong! It took less than two minutes, including opening the box and unwrapping the filter. I'll definitely be changing my filter more often - and buying it through PartSelect. Your ordering was so easy and delivery was unbelievably fast!

Totally followed the instructions of the video that came with the sensor. Unplugged the the fridge, defrosted the freezer. Cut off the main sensor that usually is the one that goes out. Installed the the new sensor with new wire terminals, crimped them and covered with electrical tape. Fridge works like a charm. Partsselect is excellent. Saved me a few hundred dollars versus having a GE Tech come and do it.

took a little more effort than the video show to remove old module and replace new. Works fine now.

It was way to ez to install only a couple of minutes that's it

Turned the old filter loose, removed the adapter from it, put the adapter on the new filter and turned the new filter back into place.