PFCF1NFCABB General Electric Refrigerator - Instructions

I watched a you tube video for 2 minutes & did the replacement in1 minute.

First, removed all items in the freezer, placed into a cooler. Removed basket and door from the glide rails. Installed new divider using two supplied screws with a nut driver. Be sure to install support bar first and align the divider by loading at an angle, push into place. Reinstalled shelf and icemaker tray, door, and basket. Can be a little tricky to install if you don't do the support bar first, and removing the door seemed necessary for adequate access to the interior of freezer.

There were no instructions on how to relpace the divider guide so it took me a while to realize that I had to remove the guide under the ice maker first. Once that was done the metal bar that supports the front of the divider guide and the divider itself could be positioned. It did take a little force to push the guide into its proper vertical position. After that the the guide under the ice maker could be replaced.

In replacing the freezer door I wasn't careful to pull both glides out together so the geared tracking mechanism came apart. Once that was put back together and carefully pulled out the freezer door was able to be replaced.

Removed ice bucket, and unplugged ice maker. Removed light cover. Removed ice maker. Pulled fan blades straight up and removed. Pushed new blades on to motor shaft. Fairly easy .

The best instructions were several YouTube videos for replacing icemakers on GE french door bottom freezer refrigerators, but none fully described the process. The following difficulties were encountered: (1) Instructions for removing the freezer door showed three screws on each side that needed to be removed; in fact, there was only one screw on each side. It was smaller than the three depicted screws and its location was not exactly as shown in the videos. (2) None of the instructions adequately described the process for removing the mounting plate from the nonfunctioning icemaker so it could be attached to the replacement unit. The key was to forcibly pry open the cover over a screw that then needed to be loosened with a screw driver. It seemed that I risked breaking the unit when I tried to slide the tab, but it eventually moved and revealed the screw that was holding the original mounting plate in place. (3) Replacing the freezer door required lining up some metal studs with slots in the undercarriage; you need to get down on the floor to examine how this fits back together. (It might help to take some photos before removing the freezer door.) (4) Replacing the upper drawer was perhaps the trickiest. My first effort resulted in having the rod with gear pinions on each end pop out because some of the tabs holding the gear pinions on each end broke. That meant that I had to order two replacement gear pinions (left and right are identical). Then, as with the freezer door, it was necessary fo slide metal studs on each side into a vertical slot leading to a horizontal slot in order to seat the upper drawer properly. So the whole process took a few weeks; actual work time was perhaps 3-4 hours. This could have been shortened significantly had I taken photos as I disassembled everything and if the procedure for moving the mounting plate had been clearer (or even existing). All in all, though, this is a doable DIY project.

Easy

So we ordered a replacement "PS2577898 GLASS COVER Vegetable PAN" and they sent us the wrong part. It sort of fits over the vegetable drawers, but our GE Fridge model has curved sides and these guys sent us a glass cover that is a perfect rectangle, which sticks out above the grooves where it's supposed to go. After a month of waiting, though, we just didn't care anymore and decided to use the part that arrived. Asking for the correct replacement may take us into 2021...

Took out the MFW filter.
Screwed in the MFW bypass.
Dispensed several gallons of water.
Saw good flow of water.
Removed MFW bypass.
Replaced MFW filter.
Our water flow was back to normal.

took a little more effort than the video show to remove old module and replace new. Works fine now.

Totally followed the instructions of the video that came with the sensor. Unplugged the the fridge, defrosted the freezer. Cut off the main sensor that usually is the one that goes out. Installed the the new sensor with new wire terminals, crimped them and covered with electrical tape. Fridge works like a charm. Partsselect is excellent. Saved me a few hundred dollars versus having a GE Tech come and do it.

I couldn’t repair the problem because the part that came did not have the clips to crimp on the end that go into the modular connection,

Turned the old filter loose, removed the adapter from it, put the adapter on the new filter and turned the new filter back into place.

We didn't think the dispenser problem was related to the filter - we were wrong! It took less than two minutes, including opening the box and unwrapping the filter. I'll definitely be changing my filter more often - and buying it through PartSelect. Your ordering was so easy and delivery was unbelievably fast!

Took cover off, pushed blade on, and replaced cover

got new filter