PCE23NGTDFSS General Electric Refrigerator - Instructions

Before I could start any repairs I first had to adapt the replacement part so it would fit the original application of the part . Tje factory original has two female ends on the water lines , the factory replacement had 1 female and 1male end . This bit of knowledge was not conveyed to me so I had to drive into town as I live out in the country and purchase the parts needed to convert it to fit my refrigerator. After the necessary parts were replaced the installation went smoothly.
If you do not have the ability to refabricated a part you should not try to attempt this you may end up with a leaky part.

Removed ice bucket, and unplugged ice maker. Removed light cover. Removed ice maker. Pulled fan blades straight up and removed. Pushed new blades on to motor shaft. Fairly easy .

spent 10 minutes trying to clip in the seal without any success. I emptied the crisper drawer and removed it flipped it over clipped the seal. replaced the drawer. Secret is to remove the drawer from the refrigerator.

The snack pan is pulled out then lifted slightly and pulled out fully. The new snack pan is then aligned in the slots and pushed in.

unscrewed old bulb and screwed in new bulb. checked and new bulb works great. less than five minutes to complete.

Unscrewed old bulb, inserted and screwed new bulb into place

Went online and read all the problem an found it could be my Air Inlet Kit...did not know it had one ..was online and ordered it...came in couple days..
to replace the damper I just remove the light at the top of the frige and the cover around it .I also removed the filter and filter cover..then the damper assembly only has 2 screws .I removed top three glass trays for more room...was a little easier than I was expecting..just about 30 minutes to hour ...(1) unplug Ref and last (plug it back in). Thanks ...

Found this site on the web. Told them my problem. They told me the most common part failure. I purched the part. Installed it per instructions. Waaa la now have a working refrigerator thank so much. U got the wife happy

I ordered a left side slider for the crisper door of my G.E. refrigerator.
II gave you the model and serial #. You sent me the wrong slider. '
shipping to me was $7.95, to return was another $9.90. I am very disappointed with your service.
The slider is not fixed yet; I am having it repaired thru the AHS. as I won't take a chance that you would send me the wrong item again.

I feel that you should have absorbed the shipping fee, as it was your error.

This part worked marvelously. I followed a YouTube video to completion. Essentially, I removed the water filter cover by squeezing the tabs on the side. Then, I removed the housing for the light based on the tabs placement. I unscrewed the lighting fixture, unplugged and set aside. After that, I removed the bottom part of the damper assembly (that's not included but virtually attached to the damper) by pulling on its tabs' placements. Then, I pulled off the damper assembly, unplugged the cords and added the new assembly WITH the inclusion of the damper gasket assembly that doesn't seem to have been a part of the old assembly. Rescrewed and reattached everything and now the fridge is as good as new!!!

I followed your video and completely dismantled the refrigerator evaporator motor, fan, brackets, and grommet, I completely cleaned the refrigerator including the cooling coils. I then ordered the evaporator motor ,fan, grommets, lid bumper, and brackets. The order would take a week to arrive. In the meantime I cleaned and reassembled all the old parts, waiting for the new ones to come. Guess what! The refrigerator was quiet as a mouse. I really did not need the new parts, but I kept them anyway just for good luck. Not bad for a refrigerator that's twenty four years old.

repair (replacement of the broken piece) took less than 2 minutes. I can't believe I waited so long to fix this. Piece was expensive, especially after shipping costs -- but now it looks brand new so I am happy.

Got a replacement drawer

replace a new blub

We were able to easily remove the existing clear section of the door shelves and replace them with the part we ordered from partselect.com. We needed to contact customer service during the order – they were efficient and friendly. The parts came quickly and were easily installed.