MWFW8300SW01 Whirlpool Washer - Instructions

I was already very familiar with the motor & drain pump, as I had disassembled my original one in attempt to find the problem & fix it. Finally, I broke down & purchased a new one. It was VERY easy to install! The most difficulty was finding the right sized board to put underneath & raise the machine up (with the dryer attached to the top of it) to place the board underneath so that I could tighten the bolts from underneath to attach the pump. After that was over, the rest was cake! Just attach the hoses & the electrical, which just clips in place & my washer is like new again! Yay! Oh, and yes, I'm a woman DIY'er.

Received water valve in three days, remove top on washer, removed old part and replaced valve with new one, real easy fix, any one could do this. PartSelect confirmed this was the problem and part I needed.

Took less than 5 minutes to replace, So Happy;-)

I watched the youtube video, then ordered the part from partselect. I then took my ipad out to the garage where I placed my washing machine and completed the removal of the old seal and installed the new one with ease. Be patient when you try and fit the new seal over the lip on the machines doorway. That was the only hard part. Once I got it started, the rest was easy. I am very happy the video was available and even easier to follow the link to order the part. Thanks! Presslerc

Followed instructions from a You Tube video. I'd recently lost my job and money is tight and I thought we could save money doing it myself. By watching the video and ordering parts from you we were able to save $500 between parts and labor. Thanks

the hardest part of the repair is having the confidence to pull all the screws and remove door etc. Dish soap was a good trick when I needed the last bit of the bellow to pop/stretch into place in step 1 of attaching the bellow.

dryer stacked on top of washer. had to lift washer and block w/2 x 4 to get under unit and replace pump

Unplug Unit, remove lower cover screws with screwdriver that has 1/4 drive at end, put 2 gallon bucket at strainer remove water. Remove inlet hose clamp and outlet hose clamp, disconnect pump motor wiring plug, aggressive push to RIGHT popped right out. put a dab of Vaseline on new units rubber base slide back in reverse order. Plugged in check for leaks put back together, Repair took less than 15 minutes, working great! WHAT I FOUND IN STRAINER: LEGO'S-CHANGE-PAPER CLIPS, enough things to destroy the impeller !

Well first of all when you buy this washer, the salesperson should tell you about checking the drain catch (ahead of the pump) and emptying out whatever get's caught in there. Never had a clue until it wouldn't work, then did a search on the internet, and darn if I didn't find specific instructions on how to open and clean out. Mine was packed full of hair pins, small change, lint, buttons, etc, all kinds of stuff. Guessing that is why the pump went out in the first place, it was so packed full that the pump could not draw any water through. But even after I cleaned it out, the pump was already shot. So called a service man, he said the pump would cost me around $200, then his labor to put it in, plus a $68 service call to just come and look at it, and $68 when he comes back to replace it. So I searched the internet for how to replace, came up with a very detailed You Tube video on how to replace Whirlpool Duet Pump. So ordered my pump from PartsSelect, just over $100, and replaced it myself. Super easy, only about 5 minutes. Thanks! —A very determined housewife!

Did not need to move washer, but had full access to left side of washer. side of water inlet valve. 1) remove 3 screws holding top cover on, on top back of unit. 2) remove 1 torque screw holding water inlet valve to washer. 3) remove 2 solenoid electrical plugs on inlet valve, noting hot and cold side. 4) using pliers remove rubber tubing by removing clamp. 5) install new inlet and follow steps backwards.

pushed knob straight on to shaft and then wife and I applauded!

The only issue I had was getting the hose from the tub re-installed, but that was my fault, the pump went right in. It couldn't have been easier. I was very pleased, received the replacement pump in just a couple of days, packaged very well for shipping, and had it installed in a matter of minutes. It took longer to take off front panel to access pump than it did to install it. Very pleased with "Part Select".....will use again!

I removed the three bottom screws and removed the plate. Removed the control panel, removed the star screw on the left side and pulled off the front panel of the machine. Loosen the bellow clamp with a phillips head and pull off the front spring clamp on the bellow. Pull off the old bellow and re installed the new one. Installed and tightened the bellow clamp and spring loaded clamp on the front of the bellow and re installed the panel, and control panel. Checked for leaks.

First thing, unpluged the washer. I removed the lower front acces panal. I then propped the washer up on 2 pint sized paint cans to reach the pump mounting screws. I disconnected the wire bundle going to the pump. Then removed the inlet and outlet hoses from the pump. Then I removed the 2 mounting screws on bottom and slide the pump to the left and removed. I then pump the new pump on the same way I took the old one off, but in reverse. Easy and fast the worst part was the price of the pump.

My dryer is on top my washer so I removed the dryer and pulled the washer out. I had to get rid of the water that was inside so I used my wet vacuum on the drain hose and sucked it out I then removed the front cover and the I tipped it back and removed two screws from the bottom of the pump bracket underneath the washer and moved the two clams on the pump hoses back to uncouple the hoses. I removed the pump and installed the new one and hocked everything back including the wires to the pump which is just a quick connect and pushed it back into place and it worked like new