MSK27PFXDAA General Electric Refrigerator - Instructions

Replaced flapper. Followed the video. The lamp caused the removable plastic bracket (which supports the control panel and the ice chute) to fuse with the plastic frame in the door. Eventually broke the fused plastic, removed the bracket, and filed the rough broken plastic before reassembly.

Remove front cover did not remove wires remove ice and water unit took off flapper put new one on 5 minutes back together

the previous left behind a side by side, everything worked however the auger in the ice bucket was a little rusty. I wish that I could say it was all me but the truth of the matter was the videos on file.

They were nicely done and easy to follow as I took the unit apart and replaced the auger in about 30 minutes. Thanks for all your help in part look up.

Replaced dispenser door flapper by following the do it yourself video in this site. It was really easy. Just be careful when removing the dispenser black bezel. I broke one of the little tabs when taking it off.

replaced the broken one with the new part

I simply removed 6 screws that held bucket to face and pit on new bucket and put it back in freezer works great

Followed the online video. Unplugged refrigerator, removed trim piece, lifted control board cover, removed 4 screws retaining circuit control board and removed the 3 connectors from the control board. Located flapper and removed by using small flat tip to take tension off flapper connectors. Helper held flash light to illuminate flapper connectors. Reversed procedure. New flapper seals well and cured problems. Circuit board was a bit different than one in video, but still had the 3 connectors. Marked each connector with grease pencil at top edge to ensure correct reconnection. Should note how wires are threaded around circuit board to ensure they are tucked back in correctly in reassembly. Remove trim piece carefully. I broke 2 of the 8 plastic pins that hold trim on. May be due to age of unit as they were brittle. 6 pins still hold trim piece flush.

I removed the plate covering the water valve for the ice maker and water dispenser, removed the nut holding the 5/16" tubing to the valve and took off the tubing and nut. I did not need to turn off the water supply or unplug the unit. I removed the kick panel in the bottom front of the refrigerator, replaced the existing plastic fitting with a new push-on fitting, then spliced the tubing coming from the water chiller to the valve where the leak was thus bypassing the broken tubing with new tubing. I reassembled the valve using the original plastic compression nut, replaced the cover and ran the water dispenser while checking for leaks. The water dispanser works great with no leaks.

Opened, discovered not flapper but more complicated

Part attaches to metal plate near crushing fingers which attaches to ice holding bin. Remove about 6 screws total on each side of plate. You must disassemble the auger & other parts so you can reassemble it in the proper order. Not many parts but i always take pics to cut down on time. New part is at the other end of the auger and acts as the holde of the auger shaft. Picture a crankshaft with a bearing on each end so the auger rotates between new part and the other end of auger shaft. That's it.

Emptied hopper
Removed screws to remove auger from existing
This was so easy I impressed my wife

1. Use skewer to press plastic tabs under control panel, 2. Remove control panel and unplug solenoid, 3. Unscrew dispenser assembly and solenoid screws, 4. Press in tabs on lamp and remove assembly - unplug, 5. Replace lamp assembly, 6. Replace solenoid assembly and fasten screws, 7. Replace flapper. 8. Replace other parts in reverse order.

son did the work BUT ONLY AFTER- trying to order the part from Sears parts online, in which they never from the right part and i spent 1 and 1/2 hours on chat and finally gave up. THEN i called sears replair, made appointment for two weeks later requesting 1st repair time of the day, was asured the repair would take place between 8-12 and beacuse it was 2 weeks away it should be the 1st repair. The day of the appt I received a phone call at 11:38 saying they would be here about 12:20, I SAID NO THANK YOU< OUR AGREEMENT WAS BY 12:00. THen I got online typrd in water tank your company come up, showed photo, and price which i ordered it can in my son fixed it and all was complete within an hr.

The video to replace the flapper looks easy, howerer the first step is to remove thestic cover of the icemaker. In my refrigerator model (as oposed to teh one shown n teh video) teh coved if firmly attached and goes under the refrigerator external plate so I was never abel to take it oot (so step 1 failed).
I was able to replace the flapper TROUGH the whole whre te ice comes from! this took lots of patients and someone with small hands!

Replace the flapper and this solved it. The video provided was excellent and allowed me to do this repair myself.