MLG19PNDWW Maytag Washer Dryer Combo - Instructions

Followed your video; replaced felt seal on front of drum, (torn in two or three places), and replaced both front guide kits,which were ground to the metal, causing the black dust, ( metal shavings). Thanks for the help, Buck. The drum support rollers were OK.

Tilted dryer back to access the two screws on the front panel, remove front panel, by raising it up 90° and pull the wires off for the door switch, first I remove the one 5/16 self tapping screw That holds the burner assembly onto the bracket, removed the hot surface igniter screw from old burner assembly, attached to new burner assembly, reinstalled burner assembly and also cleaned orifice from gas valve, also while the front cover was off I remove the fan housing cover and vacuumed out all The lint attached to the fan assembly, unit works great again.

I removed the control panel and front panel, then the brace holding in the drum. Then the drum came out easily.

Replacing the rollers is easy, use circlip pliers to remove the old circlips, replace the rollers, and reinstall the circlips.

After removing the idler pulley by removing one bolt and the spring, I replaced the idler roller, again with the circlip pliers. Then the idler arm bolts back to the motor mount, and the spring is replaced.

Reinstalling is easy - place the drum, have someone support it while you install the drum brace, then replace the front panel, then the control panel.

Using the pictoral parts diagrams on the PartSelect website, it was a logical process to disassemble the dryer to change the drum drive belt. This was a great opportunity to clean lint from the motor and air passages and inspect all components. Cleaned the belt track, the roller drum wheels and felt seals. Unit now runs like new. BTW - very fast shipping on the replacement belt and it was the right part the first time!

I removed the Drier Door and removed the Front Drier Panel exposing the Gas Valve & associated parts. I removed two (2) screws holding the Gas Valve Coils in place & replaced the 2 terminal coil, then replaced the screws, Front Cover & Drier Door. I liked the results so much, I ordered the other Gas Valve Coil and will replace it also when it arrives.

Good trouble shooting information.

Replaced coils on gas valve.

After reading the many different common stories,I replaced both coils (m series).Very simply lifted up the top of driver,held by 2 snap springs and 2 lint vent screws.Removed front cover,2 screws and 2 bottom snaps,coils down on bottom left.r/r both coils,reinstalled covers and let there be heat!This website is a blessing!!

The YouTube video on how to replace the baffels was excellent. After watching the video, it was a piece of cake.

Save the money and buy the part with partselect. My dryer problem was obvious. Before I purchased the part I jumped on YOUtube to see if there was a repair video that matched my problem. FRIELINK5 had a very thorough video. This guy did it with one hand and overall it looked easy. Then I ordered the part. When it arrived I gathered all of the tools first. Rewatched the youtube video, then installed the part. I recommend going through parts select problem determination if you do not know what is wrong. Follow the instructions and purchase the part. I saved probably over $125. House call 50$ + Labor and part $100 from a service call. TRY IT save money.

Inherited an older Maytag natural gas dryer that was not heating . Just heated at start then would not after 5 mins or so. Went to Partselect site and it had a troubleshooting section and read and narrowed down the part needed by ohming the coils. Ordered the coils for less than $20 and ordered a natural gas to propane conversion kit. Parts arrived in 2 days on regular shipping, very quick! Instruction were very simple to follow and coils were installed in under 15 mins. Propane conversion kit was perfect and was installed in 30 mins and dryer ran just like new. Cleaned inside thoroughly and couldn't be happier. Thank you partselect for great service and saving what would have been more than a $300 service call. Did myself for under $50. I highly recommend this site and will use when ever I can!!! Great service, great way to do business!!!

The dryer disassembly was pretty straightforward. The drive belt slips over the drum and easily prys over the drive and idler pulleys. The drum seal is held in place with the existing metal tabs. The old drum glides had to be drilled out and the new ones pop rivited in easily. Overall a rather simple process and the dryer sounds and drys like new again for minimal expenditure and time. Probably would have cost $200+ had I had a service person do the work.

I removed the 2 screws that hold the door and removed the door. I then removed all the screws that hold the front panel and removed the front panel. Then I was able to lift (on hinges) the top panel. I then removed the screws that hold the front drum housing, then removed the drum and belt. At that point you have plenty of room to access the idler pulley. I removed the Idler pulley spring. Then I removed the the screw holding the Idler arm and shaft. Reinstalled in reverse order.

Took off the front, took thd drum off, removed old belt, placed on new belt ptu everything back together.

Door switch was very easy to replace as it simply snaps in for the outside and you just clip on the two control wires that already have clips on them.

Removed the old hoses and screwed on the new hoses.