MLG19PDBGW Maytag Washer Dryer Combo - Instructions

After taking one last look through the access port prior to ripping the back off the dryer in order to access the heat exchanger fuse, I noticed I had inadvertantly un-plugged the gas solenoid. I reapplied the plugs to the solenoid and, voila, I had flame.

I am thankful to know I have a source in case I encounter other appliance problems, though. This one was a no-brainer but the next one might be more difficult. Thank you.

We took the washer completely apart. Replaced the bearings, pulley and
belt. We decided to replace anything that involved the spinning cycle while we had it all apart.
It was well worth the time and effort we put into it. It works like a chime
and is very quiet . Silence is golden ! Hopefully it will work another 18 years.

got instructions off internet from others who did same repair; after taking inner basket out, used drift to remove outer bearing; seal was difficult to remove but used drift to force innner bearing into seal and seal popped out. had help reinstalling inner basket into outer basket.

Took off the four screws to get to the female clip and used pliers to squeeze it out. Next was using pliers to pinch out the male connector and place the new one in.

The replacement part just snapped into place. (The old part had fallen out) It took less than 30 seconds to do the repair.

Watch the video. Very, very easy

First I put the square female end iof the door catch kit nto the square hole as snug as I could. Then I gently pushed the door against the piece until I heard it click in to place. That's it!! Sooooo simple--

Removed four philips screws, two holding door on and two on opposite side of door in order to remove front cover. Then removed two 5/16 screws holding clips that lock the top cover down. Then the top cover hinges up with open access to the drum. The baffles are held into place with two #10 x 1 1/4" screws with 5/16" head each. These had pulled through the drum. Installed new baffles (do NOT come with screws / you'll have to buy some). Had to put small washers (also had to buy) on the screws to hold it onto the drum since the other screw heads pulled through the drum. Closed lid, installed retaining clips, installed door onto frame, installed front cover around door, then screwed door hinges into front cover and screws to other side. Took about as long to write these directions as it did to actually do the work... EASY job!!

removed dryer door 4 screws
removed front panel
removed front tumbler bracket
removed blower cover
removed wires attached to heat and door sensors
removed top
removed drum and belt
removed side panel
removed clamp holding idler pulley
replaced pulley and clamp
reversed above steps

Removed and replaced both the thermostat sensor and the ignitor. Tested thej dryer and it worked. Replaced the front panel and it was good to go.

I took the door off, front panel, soap dispenser(to lift the top out of the way)and took off the cross braces on the front of the machine. I pealed the door bellows off and took the drain hose apart; there was much gunk and debris to clean out...maybe something here was clogged? Removed all the snap clips and took the front of the tub off;the tub seal seemed good, but lots of grime/gunk build up.I cleaned all surfaces, put the new tub seal on,and put it all back togther. The hardest part was working the snap clips back on; I worked a few on both sides, top and bottom, and then filled in the rest. The machine has been working fine for a month now, no leaks:)

I removed the control panel and front panel, then the brace holding in the drum. Then the drum came out easily.

Replacing the rollers is easy, use circlip pliers to remove the old circlips, replace the rollers, and reinstall the circlips.

After removing the idler pulley by removing one bolt and the spring, I replaced the idler roller, again with the circlip pliers. Then the idler arm bolts back to the motor mount, and the spring is replaced.

Reinstalling is easy - place the drum, have someone support it while you install the drum brace, then replace the front panel, then the control panel.

Did an internet search for parts for my older Maytag dryer. Landed on PartSelect and man I am glad I did! Entered my model number and boom! Complete schematics on the dryer, with part numbers. Also have diagnostic questions to point you in the right direction. Figured out what parts I needed, ordered via phone. Fantastic customer service. PartSelect also has excellent installation videos you can watch to assist. Took me a little over an hour to open up the dryer, replace the drum rollers, drum belt, idler roller and both front and rear felt seals. Buttoned dryer back up, hit the run switch and it purs like brand new. I cannot recommend PartSelect to highly. Great company, great customer service, quick shipping.

Followed your video; replaced felt seal on front of drum, (torn in two or three places), and replaced both front guide kits,which were ground to the metal, causing the black dust, ( metal shavings). Thanks for the help, Buck. The drum support rollers were OK.

Using the pictoral parts diagrams on the PartSelect website, it was a logical process to disassemble the dryer to change the drum drive belt. This was a great opportunity to clean lint from the motor and air passages and inspect all components. Cleaned the belt track, the roller drum wheels and felt seals. Unit now runs like new. BTW - very fast shipping on the replacement belt and it was the right part the first time!