MEP5775BAF19 Maytag Range - Instructions

I had to remove the screws that held the range top in place. Next just removed the existing element (leaving the wiring in place). Replace wires one at a time and then placed all the screws on the new element.

Remove the door, remove screws from all sides

Remove sides and face of oven door by sliding down from under the oven handle trim.

Remove screws on 2nd light of glass and set aside.

Now you are at the inner door panes. their should be two in an insulated type unit.

Remove the remaining screws from the handle pracket and the permiter frame for the glass/insulation. Remove permiter frame and set aside.

Pull out inner door glass frame. get a pair of pliers and bend tab on frame up so you can pull the frame sightly apart, replace the glass, secure frame tightly around glass slide tab back into reciever slot and bend down ( you may need another person to assist in keeping both lights in the frame while trying to ben tab back in to place)

reassemble door as it came apart carefull not to over tighten the screws, they strip easy.

slide stove all the way out. Remove front, then top, unhooking two wiring harnesses. Took pictures of existing wires to make sure to get back in same place. Pull element wire connections off. Replaced element and reconnected. Fairly easy.

Put a new one in.

1st - UNPLUGGED appliance from electrical source!! then removed screws to open ceramic stove top, disconnected wires from dead element, plugged in wires to new element, closed stove top, turned on burner - it worked!!

only problem is that "hot burner indicator" does NOT stay lit after burner is turned off!

The video indicating •unscrew old sensor, •pull wiring, •unplug old sensor, and •plug in replacement was good until I pulled the old one and saw wire nuts behind the small square hole! After some research, I learned that the nuts COULD come through that small hole with use of needle nose pliers. One of the wire nuts had the edges pinched off (chipped) in the process. Then I learned about ceramic wire nuts, which I'd never previously encountered. Very important if you don't want to melt your nuts! I cut and stripped the end of a disconnect plug to the stove wiring and now I have a plug in place; which, hopefully, I'll never need to use.

1. Open oven door to first detent, then pull it up off the hinges.
2. Pull oven out from counter 10-12 inches.
3. Hinges are accessible from the outside of the oven.
4. Remove 2 screws on each hinge and remove old hinges.
5. Put new hinges in place and try to insert mounting screws.
6. Wonder why screws won't start in threads.
7. Examine new hinges and notice they are not threaded for the screws.
8. Screws are not self-tapping, so go to basement and get tap & die set.
9. Use 10-24 tap to make threads in new hinges.
10. Put new hinges in place and insert mounting screws. Tighten.
11. Pull hinges to first detent and put oven door on hinges.
12. Push oven back into place in counter.

No instructions with part, so I had to look up on internet. This took more time than installing it. Think basic instructions should come with the expensive part.

I removed all the screws that held the trim and inner frame to the outside window unit first. Then, I removed a protective glass from over the two inner panes. Next after removing the frame that held the two inner glass panes together, I took the broken inner glass pane out and replaced it with the new one. Then basically I just retraced my steps and had the door put back together in about 45 minutes. You just need to pay close attention to your disassembly so that you are able to put the pieces back together quickly.

The entire "project" took me less than 3 minutes, and required no tools at all! First, the saleswoman over the phone pointed me to the correct product for my problem ($30 less than what I thought I needed), and it arrived at my home within 4 days. Then, it was just a matter of pulling off the old gasket, and snapping the new one in place! Simple!

We removed the door from the hinges by sliding it up. Then we removed all the screws holding the door together. We had to remove the screw securing the trim. Next we removed the screws inside the trim holding the old handle. We replaced the handle and trim and screws in reverse order. Finally, we re-attached the door by sliding it onto the hinges.

I took the back panel off, removed the old lens, installed the new lens. How easy to order from home, receive the part, do the repair and pay less than it costs to simply drive to the parts house. Cool....

unplug and plug in new

replacement was very easy, took 5 min

took the old one out (two phillips head screws)and put the new one in. done. took about 5-6 minutes.