MAT12PDLGW Maytag Washer - Instructions

I replaced the 3 screws because they were rusty. Then I replaced the Drain pump

Followed the first guys directions.
remove front
lift top
remove agitator
remove locking nut clockwise
remove inner tub
remove Mounting S loosen set screw and clockwise also
clean well
replace boot as shown in tip in sheet
push boot on completely

Found the parts I needed on your website along with a video that showed exactly how to do the repair. Set my iPad on the dryer and followed along step by step. Never would have tried something like this without your helpful information.

First I bought a Maytag spanner wrench on eBay, you have to have it. It was $12.00 including shipping. Then when the parts showed up the next day followed the video and had it done in just under an hour from gathering my tools and cleaning up. The video was perfect and I had no troubles what so ever. The quote from the repair services was $280.00 and I did it for less than $90.00

I propped up the machine. Turned the water off .took the pump belt off, then took the two hose clamps off. With a bucket and towels on hand for left over water in the hoses, i removed the two hoses. Then removed three screws that held the pump on. Installed the new pump in reverse order.

Loosened the set screw and removed the agitator, found nothing wrong. Replaced the agitator and tightened set screw, no more wobble.
This is a mid 1970 Maytag and a workhorse.Had three kids wash over the years, now "kids" in their late 30's and early 40' and washer is as good as new (except a little rusty)

First time I had a problem with it. Sometimes just look for the simple things !

Part select refunded me for my part that I ordered very fast.

Great Company to deal with!

First I took the door off. Undid two screws that held the top door on. Took the tub out. Make sure you have a spanner wrench. So much easier.

Received drain pump by fed ex, put it on in 15 minutes. . . My wife was very happy again. . . .

Unhooked water and drain lines, Unplugged electrical. Removed the two phillips screws at the bottom of the front cover. Removed the Front cover. TIpped machine backwards at about a 45 degree angle using a 2x4 to support the machine. Removed the pump belt and the drive belt. Installed the old pump belt and the new drive belt. Loosened the 3 each 5/16" bolts holding the pump mechanism and moved pump to the left. Moved pump to right to tighten pump belt and tightened the left pump bolt. Loosend the one pump bolt and pulled the motor to the left to tighten the drive belt and holding in this position I tightened the pump screws, Pump belt was now looser than the drive belt. Ran washer and it worked perfectly.

Used duct tape as the video provided instructed and also to hold second hinge lid ball in place. Firmly pushed down on the lid until it easily popped in place.

I first removed the front panel of the washer and removed 2 screws holding the top of washer in place. I had to flip the top up. This allowed easy access to the tub. I then removed the agitator by removing the set screw on the lower portion. From there I loosened the mounting securing device by using the nail punch and hammer inside of the tub (it was loosened by turning it clockwise). The tub was now loose and I removed it from the washer. Next I removed the torx set screw and the tapered hub unit (cork on it). It had to be again loosened with the hammer and nail punch and turning it clockwise. This exposed the part that needed to be replaced. I replaced the old with the new and the washer now works great with no leaks! Be sure to clean everything you remove that will be reassembled.

The PartSelect video was awesome in giving me confidence. The step by step instructions worked well until....

Calcium carbonate buildup on the reverse threaded spanner nut locked it in place such that I couldn't break it free.

I tried muratic (hydrochloric) acid which removed the surface scale nicely. But, no impact on allowing the nut to be pounded free. I then used a dremmel drill bit to vertically drill holes into the nut cross section. This allowed me to tap in a cold chisel and then pry the nut apart. Unfortunately, I had to repeat this for the second spanner nut as well.

Note, the first nut threads on the second part of the tub seal kit. So, drill away. You will not need these threads. however, the second set of threads you need to be carefull not to mess up. By drilling verically you can remove most of the cross section and cold chisel the rest without damaging the shaft threads. Second note: gently tap /wedge the cold chisel into your drilled out area. you don't want to hit hard and risk the ball bearings/raceway from getting ruined. Use the cold chisel to pry apart the aluminum stem hub. Its cast, so it will break pretty easily.

Net, the video allowed me to complete a project that exploded views, etc. would never have! The frozen nuts aside, this was an easy job that WORKED! No more leaks.

Followed instructions, those were OK.
Dishwasher front still leaking

I was only missing one of the bumpers but that was in pretty poor shape so I replaced them both. It didn't take much to do. Just pressed the bumper into place and Viola! instant gratification.

I followed the others directions and it's important to note that both nuts involed are indeed left handed threads. Also the it's important to know that[at least on my machine] that the set screw on the agitator is a torx headed set srew, not an allen srew. Other than that it was a pretty quick fix.