MAT12PDBAL Maytag Washer - Instructions

Cleaned the cavities. Lubed them with olive oil. Inserted one ball on left side, while holding tension against that side to hold the ball in the lid and top indentations. Applied olive oil to right hand side indentation, and placed the new ball into lid indentation. Put lid down into closure cavity with ball, and with lid vertical, began pushing it rearward so as toslightly spring metal lid rolled edge and top metal away from one another UNTIL the new ball snapped into the hinge indentation in the machine cover. Done.

removed control pannel, traced current flow to lid switch,in but not through, shorted power in to motor lead machine started, ordered switch, received switch, installed new switch, washed clothes.

Removed top. Removed agitator and tubs . Replaced seals and reassembled.

Remove the power cord and water hoses. Lay the machine on the floor. Remove two belts (washing and pumping). Unlock the screw of pulley using a hex key. Remove the broken pulley from the motor. Place in the new pulley. Lock the screw of the pulley. Install two belts. Turn the machine vertically. Plug in water hoses and power cord. Level the machine.

Removed the old hoses and screwed on the new hoses.

well i first put on 2 new belts because they were worn and smoking. the new belts did not fix the problem. you suggested putting in a new pulley. it went against my better judgement that the pulley was defective. well i put in the new pulley and now the real problem has surfaced. the transmission is not working. now i want to order a new tranny and low and behold it is no longer available. well why did you sell me a $99 pulley when that was not the next part to change after the belts were replaced. now i have a new pulley on a washer that is going to the recycle center as metal trash. well on my part i will reward maytag by buying a ge washer now. plus i will not count on using you as my parts supplier.

Removed tubs per prescribed videos. Removed transmission per video. Disassembled transmission per video. Used heat and penetrating oil to free top shaft. Lubricated top shaft and bushings with grease and reinstalled. Reassembled washer with replacement parts from partselect. Problem solved. My wife loves this washer. It lasted 30 years before I had issues, many of the internals looked brand new. They dont make' m like this anymore. With the self- help videos, and OEM parts from partselect, I'll get another 30, Thank you so much.

Took off the upper back that had 6 screws with a screw driver. Found the lid switch . Removed it after I figured out how to remove it. It was a little tricky without instructions. Putting in the new switch was a little tricky also. You have to angle the front of the switch in, pop it in and then push it back so it can snap in. Once I put it in, the washer started right up. I was very happy. Instructions would have been very helpful. I am very pleased with this company because I received my switch in a couple of days. I will definitely use this company again.

Layed the machine on it'sback and put the 2 belts on the pulleys,Very easy ,when you know to put the machine on it's backside!

Could not repair. The gearbox on the agitator was broken and that kept the agitator from working. Do not assume it is a belt problem on a washer built in 1987.

I followed the instructions on this website to a T. You can take the front cover off and you will notice a small drip from the tub area where the Hub bearings (above the tranny) meets the washing tub. Once you've identified that the leak is indeed coming from that area and not a loose tube. Allow the washer to complete the job and drain the water. Then simply unplug washing machine before starting the process of the repair. It is very important to remember that you must have a spanner wrench before attempting to perform this repair. keywords=spanner+wrench came within two days with Prime Shipping. Also be sure to order the replacement parts from this site. It takes about 3 days to arrive however so be prepared to be without a washer for a few days. Other than that just follow the instructions provided and there is a very good step-by-step video on this site .

I followed the direction came with the part.

• I unplugged power electric wire from the wall.
• Unscrewed total of five screws from the back of the top console.
• Removed the top console to gain access the switch.
• I took pictures of the switch position for a future reference.
• Unplugged the switch wire by just pulling the plug.
• Carefully removed the switch and pulled the plunger out plunger assembly.
• Entered a new plunger in first and inserted a new switched carefully.
• Opened and close the lid few times to check the switch is going on an off properly. You will hear clicking sounds.
• Plugged the switch wire to the new switch.
• Reinstalled the console and screwed back the five screws.
• Plugged back the electric plug in wall outlet.
• Tested the washer by washing a full load of clothes.

The whole process took me about 30 minutes.

-Abhay

Removed the bottom belts to inspect. Belt for tub was well beyond it's service life. Belt for pump was OK. ordered the pair and replaced. When the washer was started the agitator still did not move. With power off I grabbed the agitator and pulled upward a few times then twisted it from side to side a few times. No change. Then I did the same with it with powered up ( a bit dangerous ). The agitator then ran OK.

There are two screws that hold the switch in place. And two wires connected to the switch. The most difficult part of replacement is to place the new switch and hold it in place to reinstall the mounting screws. The space to work in is limited unless you remove the front panel from the dryer, which I opted not to do.

took front panel off had 2 screws, propped up washer in front, took belts off with hands and put new ones on in reverse order One belt was badly cracked. I am 77 year old female, if I can do it, anybody can. great service on getting belts too. Thank you