MAT12PDABL Maytag Washer - Instructions

new replacement water pump leaked where plastic housing upper and lower halves were bonded, presumably with glue. As a quick fix I wrapped pump with some 3M 4411N sealing tape. Seems to have stopped or really slowed leak. I was going to get another new pump but now worried it will leak as well so going to see how long tape fix works..

all went well until testing. tub level did not shut the water off, caused a spill

Top came off quickly with socket wrench. Removed gasket in about a minute. Spent 45 minutes getting grime ( soap and lime) off of top. Took five minutes to replace gasket.

Haven't been able to get front back on. Clips go on side rather than top. Found missing clip for which new one was purchased in transmission. Still haven't gotten front to stay on. Clips keep springing out.

A friend said the cause was probably a belt. On Google we checked the washer model number which took us to your site. We looked at the videos on how to do the repairs, and so ordered a drive belt and pump belt. They arrived in two days. My husband is 84-years-old, I'm 83 -- difficult for us to lift the machine to tilt it. Experimenting with fulcrum and lever, we managed -- that's what took so long. After watching the videos again, I laid on the floor and was able to apply the belts. Washer works great!

Followed the directions posted by another user. His tips were very important and helpful. At first we only ordered parts where it was leaking, then decided we might as well change the remaining parts as recommended by the other user in his description. This is the FIRST issue we have had in 19 years of use. Ordered the parts, received them quickly and correctly. Installed them and it works like a new machine. This Maytag will probably last another 19 years.

Repair not that complicated. Remove front, lean top back, remove agitator, remove special nut, remove inner tub, remove seal. Clean shaft and seal surfaces. It is highly recommended to the spanner wrench to remove the special nut. It appears one can do it with a punch and hammer, but the nut is too tight, and corroded from years of water exposure. I believe part number is TJ90TB123A, about $15. Watch the video on this web site, very good.

Followed the instructions on-line. Pulled the washer out from the wall, tipped it back about 45 deg. & removed the two philips screws as the base of the front of the washer.Removed the old belts which showed little wear, disconnected the hoses from the pump. Replaced the pump which was held in by only 3 nut-head screws, attached the belts & adjusted the tesnion as described on the website.

Two screws holding top, unhook wire conector. remove cabinet,replace switch. Reassemble.

watch the video and it was very simple replace belts like they show on the video. lay the washer on it back and the belts was visabile. removed the small belt and then removed large belt, and replace the large belt and small belt. i used no tools. that because i lay the machine on it back.

I removed the two screws holding the switch and removed it from the machine. I then removed the broken spring and replaced it with the new one sent to me from partselect.com. I reinstalled the repaired switch and turned on the machine. It was easy as that and it works great. PartSelect.com is the best.

My dryer is 35 years old and thought this was it, but I googled the question and found out it was the door switch. Orderd the part and received it very fast and didn't want to wait for my husband to come home so I went on you tube and found a video how to open dryer and change switch. I did it in about 30 min. and yes it is now perfect again. No problems. I just unscrewed the old switch and put the new one in. Maybe I'll get another 35 years out of this machine. :o) Thanks for making it so easy.

Order the part and put the new part on and put the washing machine cabinet back on and check the washer for the water filled up and then it's starting to go on the spin cycles.

Removed the front panel with a screw driver, removed the old bumpers with a pair of pliers, replaced the bumpers and replaced the panel. All was very simple and took no time. The video on your website was most helpful. Thanks

Unplug washer and shut off water valves. Remove water hoses from the faucets and caught the water in the hoses in a bucket. I removed the drain hose from the back of the washer and caught the water in the bucket. Remove front panel by removing 2-screws at bottom and tilting it out to come off. Disconnected the hoses to the pump and caught most of the water in the bucket.. An old towel stuffed under the bottom pan of the washer, under the pump hole caught most of the rest of the water. Tip the washer on its back and removed the belt coming from the motor. Removed 3-screws that hold the pump on and angled the pulley end through the hole in the bottom of the washer. I just reversed the procedure to install the new pump and everything else. I would have replaced the hoses and belts, but I had just done that about a couple of years ago, when I replaced the connector at the top back of the washer for the hose from the pump and hose to the drain in the wall, that had a crack in it and was leaking.

Loosened the set screw and removed the agitator, found nothing wrong. Replaced the agitator and tightened set screw, no more wobble.
This is a mid 1970 Maytag and a workhorse.Had three kids wash over the years, now "kids" in their late 30's and early 40' and washer is as good as new (except a little rusty)

First time I had a problem with it. Sometimes just look for the simple things !

Part select refunded me for my part that I ordered very fast.

Great Company to deal with!