MAT12CSAKQ Maytag Washer - Instructions

Switch material hardened due to old age & broke easily when force fitted. Ordered parts online & in two business day it arrived.

First open the lid & removed the side latch with screw driver carefully. Checked the length of the new plunger with the old one with respect to length & compare the stroke. Slide fit the switch & rectified the play in the plunger pusher with super glue.

iremove the two screws that is on the lid and then ipulled that out then secound step remove the part is on the back were is the suit of the washer machine were is the hoses of the water hot and cold its berry easy to do it your self thank you

Removed the damaged legs, replaced with parts from this site and leveled the washer .

After turning the water off and unplugging the machine, I took the front panel off the washing machine. I then slipped the belt off the pump sprocket. The pump was right in the front and easy to remove. All I needed was a screwdriver, for the hose clamps, and a 5/16" socket to remove the old pump. I then installed the new pump, with the existing screws, re-attached the 2 hoses, slipped the belt back on, and popped the front panel back into place. The new pump works great and the leak is gone. The whole job onlt took about 30 minutes.

Lets just say thank god for part select!!!! # 1 By far. This was a one two three job.

Found noise to be belt slapping the base sheet metal, from being too loose. Belt was loose because the drive pulley was worn and one side of pulley was loose! Used allen wrench to loosen the pulley set screw, and pryed off the old pulley. Replace d with new pulley and new belts. Works and sounds like new!

removed control pannel, traced current flow to lid switch,in but not through, shorted power in to motor lead machine started, ordered switch, received switch, installed new switch, washed clothes.

Cleaned the cavities. Lubed them with olive oil. Inserted one ball on left side, while holding tension against that side to hold the ball in the lid and top indentations. Applied olive oil to right hand side indentation, and placed the new ball into lid indentation. Put lid down into closure cavity with ball, and with lid vertical, began pushing it rearward so as toslightly spring metal lid rolled edge and top metal away from one another UNTIL the new ball snapped into the hinge indentation in the machine cover. Done.

Removed top. Removed agitator and tubs . Replaced seals and reassembled.

Removed tubs per prescribed videos. Removed transmission per video. Disassembled transmission per video. Used heat and penetrating oil to free top shaft. Lubricated top shaft and bushings with grease and reinstalled. Reassembled washer with replacement parts from partselect. Problem solved. My wife loves this washer. It lasted 30 years before I had issues, many of the internals looked brand new. They dont make' m like this anymore. With the self- help videos, and OEM parts from partselect, I'll get another 30, Thank you so much.

Took off the upper back that had 6 screws with a screw driver. Found the lid switch . Removed it after I figured out how to remove it. It was a little tricky without instructions. Putting in the new switch was a little tricky also. You have to angle the front of the switch in, pop it in and then push it back so it can snap in. Once I put it in, the washer started right up. I was very happy. Instructions would have been very helpful. I am very pleased with this company because I received my switch in a couple of days. I will definitely use this company again.

Layed the machine on it'sback and put the 2 belts on the pulleys,Very easy ,when you know to put the machine on it's backside!

took front panel off had 2 screws, propped up washer in front, took belts off with hands and put new ones on in reverse order One belt was badly cracked. I am 77 year old female, if I can do it, anybody can. great service on getting belts too. Thank you

Pull washer out from wall. Remove front panel (2 Philips head screws), swing bottom of panel out, remove panel. Tilt washer backwards, lean against wall to expose area under washer. Roll off old belts, roll on new belts. Move washer back upright, replace front panel, replace the philips screws, move washer back to original position.

Partselect.com gave me a very helpful list of parts per symptom. Said that there is an 88% chance that belts were my problem. Since the machine is 200 miles away I ordered two other parts as well. Belts fixed it! Took front cover off (not totally necessary). When the machine is tilted back belts are exposed underneath. Two belts later I was up and running. This site is really great.