MAT12CSAAL Maytag Washer - Instructions

Lets just say thank god for part select!!!! # 1 By far. This was a one two three job.

I turned the dial to other selections and nothing worked, no power. I checked the fuse box, but nothing was off, and then I checked to make sure electricity was working with a light bulb. I googled the situation and came across this site and read other posts as they sounded exactly like what I was experiencing. I ordered the complete lid assembly not just the fuse. The item arrived quickly in two days. After about an hour, as it was pretty easy to replace, the washer was working again! Thank you all for posting, as it saved me at least a couple hundred dollars.

Found noise to be belt slapping the base sheet metal, from being too loose. Belt was loose because the drive pulley was worn and one side of pulley was loose! Used allen wrench to loosen the pulley set screw, and pryed off the old pulley. Replace d with new pulley and new belts. Works and sounds like new!

Cleaned the cavities. Lubed them with olive oil. Inserted one ball on left side, while holding tension against that side to hold the ball in the lid and top indentations. Applied olive oil to right hand side indentation, and placed the new ball into lid indentation. Put lid down into closure cavity with ball, and with lid vertical, began pushing it rearward so as toslightly spring metal lid rolled edge and top metal away from one another UNTIL the new ball snapped into the hinge indentation in the machine cover. Done.

Removed top. Removed agitator and tubs . Replaced seals and reassembled.

removed control pannel, traced current flow to lid switch,in but not through, shorted power in to motor lead machine started, ordered switch, received switch, installed new switch, washed clothes.

I followed the direction came with the part.

• I unplugged power electric wire from the wall.
• Unscrewed total of five screws from the back of the top console.
• Removed the top console to gain access the switch.
• I took pictures of the switch position for a future reference.
• Unplugged the switch wire by just pulling the plug.
• Carefully removed the switch and pulled the plunger out plunger assembly.
• Entered a new plunger in first and inserted a new switched carefully.
• Opened and close the lid few times to check the switch is going on an off properly. You will hear clicking sounds.
• Plugged the switch wire to the new switch.
• Reinstalled the console and screwed back the five screws.
• Plugged back the electric plug in wall outlet.
• Tested the washer by washing a full load of clothes.

The whole process took me about 30 minutes.

-Abhay

Removed the bottom belts to inspect. Belt for tub was well beyond it's service life. Belt for pump was OK. ordered the pair and replaced. When the washer was started the agitator still did not move. With power off I grabbed the agitator and pulled upward a few times then twisted it from side to side a few times. No change. Then I did the same with it with powered up ( a bit dangerous ). The agitator then ran OK.

Took the back plate off, popped the old lid switch out and the new one in. Very easy. No problems, saved $100 buck at least doing it myself.

Remove the power cord and water hoses. Lay the machine on the floor. Remove two belts (washing and pumping). Unlock the screw of pulley using a hex key. Remove the broken pulley from the motor. Place in the new pulley. Lock the screw of the pulley. Install two belts. Turn the machine vertically. Plug in water hoses and power cord. Level the machine.

Replaced both the drive belt and pump belt in less than 10 minutes. Maytag has the easiest machines to work on.

Installed drive and pump belt.. very very simple. only tool required was a screw drive to remove front panel of the washing machine.

Removed tubs per prescribed videos. Removed transmission per video. Disassembled transmission per video. Used heat and penetrating oil to free top shaft. Lubricated top shaft and bushings with grease and reinstalled. Reassembled washer with replacement parts from partselect. Problem solved. My wife loves this washer. It lasted 30 years before I had issues, many of the internals looked brand new. They dont make' m like this anymore. With the self- help videos, and OEM parts from partselect, I'll get another 30, Thank you so much.

took front panel off had 2 screws, propped up washer in front, took belts off with hands and put new ones on in reverse order One belt was badly cracked. I am 77 year old female, if I can do it, anybody can. great service on getting belts too. Thank you

Pull washer out from wall. Remove front panel (2 Philips head screws), swing bottom of panel out, remove panel. Tilt washer backwards, lean against wall to expose area under washer. Roll off old belts, roll on new belts. Move washer back upright, replace front panel, replace the philips screws, move washer back to original position.