MAT11PDABL Maytag Washer - Instructions

My washer was sitting in a safety drain pan which made it difficult to work on due to the height of the pan walls. Managed to tilt it back and support on blocks well enough to access underside. Found two of the four leveling feet had fallen off, which was the ultimate cause of the problems from the cumulative effect of running unbalanced over time. Reinstalled these feet and had to remove rust to do so. I added two more nuts to the front feet to hold the adjustment tight. After adjusting to level, washer ran great and was no longer prone to unbalance. Procedure: Remove front panel- two lower screws and pry/pull off. Remove hoses at pump. Remove 3 mounting screws from pump. Remove belt from pump pulley. Push motor towards center of washer to release tension from other belt, and remove belt. Replace with new belt. Replaced old drain hose to pump and replaced all hose clamps with new. Install pump, replace pump belt. Level the washer. Replace front panel. Take the opportunity while the washer is open to clean out the dust from inside!

Disconnected the hoses , power cord, and the drain hose. Tipped the washer on it's front panel and removed the old belt and spun the new one on. Tested for tightness as per the instructions and sat the washer up and hooked everything up. Total time---5-10 minutes.
Local appliance dealer insisted this wasn't the belt we needed. Thanks to your website we easily selected the right one. Thanks.

1. Remove front panel with phillips screw driver.

2. Remove hose from drum and exit pump

3. replace hose with new one (used some silicone grease on hose)

4. Tightened clamps with nut driver

5. ran a couple loads of wash to check for leaks

6. found none

7. replaced front panel - Job done

Removed front door from washer lifted front of washer off floor and removed belt’s put washer back on floor
Removed motor and slide
Cleaned and replaced slides and greased put back in washer secured
Then lifted front of washer back up replaced new belts and started the washer up worked great put front of washer back on done
Great instructions that came with parts

A friend said the cause was probably a belt. On Google we checked the washer model number which took us to your site. We looked at the videos on how to do the repairs, and so ordered a drive belt and pump belt. They arrived in two days. My husband is 84-years-old, I'm 83 -- difficult for us to lift the machine to tilt it. Experimenting with fulcrum and lever, we managed -- that's what took so long. After watching the videos again, I laid on the floor and was able to apply the belts. Washer works great!

new replacement water pump leaked where plastic housing upper and lower halves were bonded, presumably with glue. As a quick fix I wrapped pump with some 3M 4411N sealing tape. Seems to have stopped or really slowed leak. I was going to get another new pump but now worried it will leak as well so going to see how long tape fix works..

Followed the instructions on-line. Pulled the washer out from the wall, tipped it back about 45 deg. & removed the two philips screws as the base of the front of the washer.Removed the old belts which showed little wear, disconnected the hoses from the pump. Replaced the pump which was held in by only 3 nut-head screws, attached the belts & adjusted the tesnion as described on the website.

Repair not that complicated. Remove front, lean top back, remove agitator, remove special nut, remove inner tub, remove seal. Clean shaft and seal surfaces. It is highly recommended to the spanner wrench to remove the special nut. It appears one can do it with a punch and hammer, but the nut is too tight, and corroded from years of water exposure. I believe part number is TJ90TB123A, about $15. Watch the video on this web site, very good.

Two screws holding top, unhook wire conector. remove cabinet,replace switch. Reassemble.

First I removed the two screws that held the front washer panel in place. Then I removed the two bolts that held the top on the washer. I then had to remove the four screws that held the top panel with the electrical parts in place in order to obtain access to the inside area where the screw was that held the fill injector was located. I next removed the screw that held the fill injector unit in place. I then pulled on the tab that held it in place and moved unit into a better place to replace the fill injector. I had previously cut the hose clamp during my investigation of the problem and replaced it with a pressure clamp. I then unscrewed the clamp, removed the bad fill injector and replaced with new fill injector. I then reversed the entire process to reassemble. The whole process turned out to be easier than I thought! The hardest part was diagnosing the problem in the first place.

My dryer is 35 years old and thought this was it, but I googled the question and found out it was the door switch. Orderd the part and received it very fast and didn't want to wait for my husband to come home so I went on you tube and found a video how to open dryer and change switch. I did it in about 30 min. and yes it is now perfect again. No problems. I just unscrewed the old switch and put the new one in. Maybe I'll get another 35 years out of this machine. :o) Thanks for making it so easy.

watch the video and it was very simple replace belts like they show on the video. lay the washer on it back and the belts was visabile. removed the small belt and then removed large belt, and replace the large belt and small belt. i used no tools. that because i lay the machine on it back.

I removed the two screws holding the switch and removed it from the machine. I then removed the broken spring and replaced it with the new one sent to me from partselect.com. I reinstalled the repaired switch and turned on the machine. It was easy as that and it works great. PartSelect.com is the best.

Then found agitator shaft was rusted to spin shaft. Worked on that for awhile. Motor then burnt out. I quit and bought new machine. I had ordered a top end seal from you guys. I trashed the machine before your seal arrived. Called you. Nice lady said she would send an E mail so I could return unused seal. That message has not arrived yet.
Pat Wehling

Since my missus keeps her appliances like new, it behoves us to buy something of good quality when new. We did that. Now, after almost 20 years, the washer complained it needed new belts, which I complied. Tilted it up against the wall after pulling power cord. Removed both belts and replaced. Adjusted pump belt by loosening pump and then retightening. This is easy to get to by removing front (removing 2 philips screws). Piece of cake.