MAH20PDAWW Maytag Washer - Instructions

Moldy bellow was the reason I replaced the bellow. It tried cleaning the bellow numerous time over the last five year, but once the mold sets in, it's a losing battle. A highly mold resistant bellow would be nice. The available video was invaluable. I would not have purchased the parts if I had not seen the video. I spent a few more dollars for additional parts, because once I got started I did not want to find a bad part and then not be able to complete the repair in one try. Since the bellow was moldy, I expected the door boot drain hose would be moldy also, so, for a few more dollars, I replace it also. Worth the effort. I took me, just under two hours to complete the job, with the help of my wife. I'm some may be thinking, what did she do? She cleaned the parts I took off, so they were clean, well at least cleaner, when I put them back on. This washer was nearly ten year old and had never been apart. I could have finished the replacement bellow in less than an hour, but I took some time to clean inside the washer while it was apart. That's just the way I roll. Fitting the bellow to seal properly was not as simple as the repairman made it look on the video, but that was because he had done this before, probably many time over. He knew what it felt like to fit it and snap it into place. Once I got the feel of seating the bellow, it went smoothly. The boot cable and spring are a bit tricky to hook, as anticipated; I read some previous experiences. So, I thought about how I was going to secure the spring in order to stretch it to the other cable hook. I decided to use two pairs of vice grips to hold the spring and cable hook end. I have two small to medium sized vice grips, which worked perfectly. Otherwise, it is very difficult to pull and hold a pair of pliers closed, at the same time. I sit at a computer most days and am not used to a mechanics world. Use your brain when you don't have the brawn. Job done, no leaks.

remove door phillips remove front push down and pry out remove soap tray phillips remove two nut screws to lift up topy open tie or support top up remove bad contactor phillips normaly open check with continunity tester replace and reverse procedure

Had to remove the door, the face of the washer, and two face pieces between the washer and the stacked drier. I then removed and replaced the bellow. The installation of the new bellow was difficult, the first time. Getting the silicone part onto the tub is tricky as is re-installing the cable and spring. I must have not gotten the cable properly seated on the lower lip as it leaked and I hade to repeat the job the next day. The second time around was much easier. There is a learning curve, even for me, a retired electro mechanical tech. I thing someone who is not very handy would have trouble with it. This repair should be considered only by someone of intermediate or better skills.

Followed the video, besides the spring, everything was easy.

I just followed what others have already noted. The only challenge was the spring as others have already stated many times. You will need help but be patient and you'll make it work.

removed front panel. removed brakets holding top. lifted top hinged backward. Removed tension spring and cable that secures the seal to the drum. Pulled seal out. Put new seal back in. Secured with cable and spring. Reassembled top and front.

easywaterways to diagnos and order the part. Very satisfied.

After removing the door, I pryd the bellows from the front of the washer then removed the front panel. I then rolled the spring from the rear of the Bellow and removed the old Bellow. Once I saw that the front edge of the washer drum was held on with spring clips I decided to remove it and clean the inside of that while I was in there. To get that part out I had to remove a couple cross braces. After cleaning I put it all back together. Getting the spring back on the back of the Bellow was a little challenging. Then put it all back together again. Now it looks great again.

Replaced the belt and motor isolators. Watching your video made it very easy.

remove door with Phillips remove front panel nut driver remove soap tray lid and lift up top Phillips test small contactors for continuity and replace removed locking sprocket and replaced

Video repair instructions on the Parts Select site was right on and made the repair very easy. I took a little longer in my repair as I cleaned each piece I took off to make sure there was no dirt/lint/rust/mold remaining. The only difficult part was putting the spring back in place, this took a couple of tries. Other than that, relatively easy to replace and would recommend that anyone with any handyman skill to do this repair/replacement themselves.

Found the part on parts select, which also had a very helpful DIY repair video to replace the part. I followed the video step by step to fix the tub cover, and the washer is back to full working condition!!! I could not be happier with Partselect.com. Their easy appliance break down to find the exact part that is broken; but to also include a instructional video for that part was amazing.

The front seal had a long slit which leaks water during washing cycle. We followed the repair video every steps and got the old seal off really easy, the most difficult step is to tie the cable with the spring, it is too strong and can not be done with one person. All steps are the same as shown in the video. Thank you for providing the video and the part.

Well, if a picture is worth a thousand words, the repair video is priceless! Without it, this repair would have been more difficult, but it was so easy to follow along with the video while doing the repair. I rated it easy, but the reinstallation of the wire and spring holding the bellow in place requires significant pulling power. It took a couple tries to get it on, but other than that, the rest of it is cake. From start to finish, the job took less than an hour, but set aside some time for cleaning behind the washing machine if you haven't pulled it out in a while! Also, I have to mention that the part I received was an identical genuine Maytag part and not a remanufactured knock off. The fit and finish was perfect.

We read the instructions on the website which were very useful. We have a Maytag front loader. The instructions and pictures which came with the part are written to look like the hardware in the door and the door latch spring etc. is attached to the outer door. I realize this part fits multiple brands but instructions could clearly state that you have to remove all of the hardware from the inner door liner that you are replacing and reassemble it to the new inner door liner. It is really important to take pictures of how the door latch and spring are attached as this took the most time putting back on the new door liner. Our washer is older and did not have a vent tube and now has one. In the end, everything was correctly reassembled and we no longer have a leaky door. Shipping was very prompt and we're pleased with the part and repair.