LSFS213ST (ASTCNA2) LG Refrigerator - Instructions

Unplugged the frig and removed two phillip screws on flapper door of left door... Unplugged the electrical connector and removed flapper...
Picked up new flapper and snapped electrical contractor together... Slid new flapper bar into place and inserted two phillip screws... Job complete in 15 minutes...

I am a73 year old woman. If I can do this, anyone can. Super easy. Just watch the online video.

REMOVED 4 SCREWS HOLDING UNIT IT DISCONECTED PLUG TO CONTROLER AND REMOVED IT BY PULLING OUT ON THE BOTTOM FIRST. TO INSTALL SLIDE THE UNIT UP AND IN FROM THE BOTTOM CONNECT THE PLUG AND INSTALL THE SCREWS. THE TOP SCREW HAS A PLASTIC SPACER WASHER. UNIT WILL NOT START TO MAKE ICE UNTILL IT REACHES TEMPATURE, GIVE IT TIME. WATER DESPENSER WILL WORK. CONTROLS ON THE FRONT OF THE DOOR WILL LIGHT UP NORMALY. I REMOVED MINE WHILE WAITING FOR PART TO ARRIVE, 4 DAYS. EVERYTHING WORKED EXCEPT WATER & ICE DESPENSER AND CONTROL DISPLAY ON THE DOOR.

I watched a couple of You Tube videos on how to make the repair, ordered a new spring from Part Select, and installed the new spring when it arrived. Took about 5 minutes for the actual repair.

Check the spring when it arrives. The first one I received was wound the wrong direction. Called customer service and they were super. Refunded the charge for the first spring, found the correct one for me, and mailed it out.

Followed Youtube video provided on the PartsSelect Website:

https://www.partselect.com/PS12374439-LG-AGU75188619-PLATE-ASSEMBLY-FRONT.htm?Inventory=12374439&SourceCode=20&SearchTerm=LFX28979ST

Made installation of the new part a piece of cake. Easy peasy!! Took less than 10 minutes.

The spring broke on the flapper (mullion) on my refrigerator. I sent a chat message to PartsSelect (they answered right away) to see if they had a replacement spring but it was not available so had to order the whole mullion. They gave me the part # I would have to order. It arrived quickly. The new mullion didn’t have a visible spring but it worked the same if not better. I just had to remove 2 screws on the center plate on the existing mullion, pull the plate out enough so you will be able to slide the mullion (the wires are under the plate kind of like the ones you see on a ceiling smoke detector) but you can’t get under the plate until you release the mullion. Push up on the mullion so that the plastic tabs on the top and bottom are released. Once the mullion is released (you have to hold it), you’ll see the wires. Unhook the wire part by just pushing down on the little tab and remove it. To install the new one, just reverse the steps. Align the top and bottom plastic tabs to fit into the slots, just enough to hold it in place. If the plastic tabs are not already flipped out, you’ll have to just flip them out. The top tab does not have tension but the bottom tab has tension so just push on it with your finger to flip it out. The plate covering the electrical is a rather tight fit and you have to make sure the little tab on the inside of the plate is above and behind the tab on the inside where the wires are so it slides behind it so you can get it in position before sliding the mullion back down into place and the electrical plate is in place too. Then screw the 2 screws back in. The hardest part is holding the mullion while un-attaching the electrical and just make sure you stuff the wires in enough so you can get the plate back in position. I’m a 75 yr old woman and managed fine by myself. At first when installing the new one, I couldn’t slide the mullion down enough to get the electrical plate in position and then realized I had to have the little tab inside the electrical plate behind the tab inside the wire compartment so they didn’t hit one another when pushing the mullion back down. Then, all went fine.

Pulled the fridge out.
Unscrewed the back cover and the one screw holding the value assemble.
undid the 2 hoses and replaced the part.

Super SImple/

Removed ice bin
Unscrew the 3 screws.
Lift ice maker for the bottom to remove it but do not pull it until the power is unplug from the part.
Install the new part the same way you removed the old part.
Turn the switch and waiting 48 hours before the ice bin start getting ice

I actually didn't use what I got. Because there was all kinds of tubing coiled up in the door. We just fed the exsess all the way through the Fridge,and Bingo! It was done.

Six screws to remove the old one (I looked up the process on Youtube) and six screws had it back in tip top shape.
Three wire connections, two were plug in and one was a ground wire.
BTW: It was a 3 wire, not a 6 wire. I had ordered that by mistake and PartSelect made the return and replacement very easy.

Just had to slip the 2 pegs into the existing holes.

i changed the filter and was able to get water to the white coil at the bottom of the dispenser (left door) but could never get water to the icemalker.i also replaced the pump at the bottom of the door as well as the green ebr699172 dispenser electrical board.still can not get water to the icemaker.any help will be greatly appreciated.
paul

Followed directions that came with the filter. Did remove the top shelf for easier access. Very simple and quick.

Watched tube video about the repair
Ordered part
Performed repair as per the video

unfortunately my fridge stopped working. I purchased another but wanted to try and repair the old one. when ew one arrived, the old one was supposed to be put in garage but instead was hauled away. Had delivery return next day but they had as already removed and lost the handle screw for the bottom freezer and the screw that holds handle in place. ordered the handle screw and picked up the nut. very simple to install the screw and put handle back on.