All Installation Instructions for Frigidaire Refrigerator LFHT1817LF4

The ends broke from the rails.

I unscrewed the old rails and took the number to order on the first day. The order came on the 3rd day. Can you imagine such fast service.
My daughter is a single mom with 4 children, one of whom was responsible for the breakage. I am the grandmother and was very grateful for the fast service and great price. The drawer was installed in 10 minutes. I just screwed the old screw into the new part and replaced the drawer. Thanks

Parts Used:

Drawer Support Rail - Right Side

Drawer Support Rail - Left Side

Maria from Sault Sainte Marie, MI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

12 of 12 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Freezer Freezing up and blocking the vent for refrigerator, not cooling the fridge.

Went pretty straight forward, except the heat shrink tubing was about 2 sizes too big. Would not shrink small enough to seal the connections. Even with a heat gun it would not shrink small enough. OH, another think is when I plugged the fridge back in the defrost timer was in defrost mode. Took me a few minutes to figure that out and use a screwdriver to turn the timer back to the on position. Other than that, install was pretty simple.

Parts Used:

Defrost Thermostat

Defrost Timer - 120V 60Hz

Dennis from BEAUMONT, TX
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver

16 of 25 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Plastic fan broke

took the cover off
(cardbord) the fan will come off and go back on by hand no tools needed i changed the fan motor just to be sure. 3 little screws hold it on. the plug only goes on one way u can't mess it up.very easy job u shouldn't have any problems doing it.Jim

Parts Used:

Condenser Fan Motor

BLADE-CONDENSER FAN

James from GLEN FLORA, TX
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set, Wrench set

13 of 16 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Plastic Shelf Broke

Snapped in place in less than 30 seconds

Parts Used:

Refrigerator Door Shelf Bin

Jim from Carlsbad, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

11 of 11 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Bottom shelf on door cracked and broke

I ordered the Door Shelf Bin from PartSelect.com on Friday and received it on Saturday!! I was shocked, but thrilled. The easy to use diagram helped me to pick the right part and I easily replaced the broken one. I have already started to recommend PartSelect.com I was so thrilled with their service!

Parts Used:

Refrigerator Door Shelf Bin

Jamie from Greensburg, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

12 of 14 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Crisper Pan

Just removed the broken pan and installed the new one within 2 minutes. Really simple

Parts Used:

Refrigerator Crisper Pan

Deepankar from Novi, MI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

13 of 20 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

No shelf in Freezer compartment though obvious slots provided.

Used model # of frigidaire on your web site... reviewed parts available... noticed shelves abailable... zoomed in to measure using crosshatch background... measured my freezer compartment... seemed doable... ordered shelf... receivednext day... attempted to slip in slots... had to grind off 3/16th inch on two legs... slipped in... Perfect!

Parts Used:

Freezer Shelf

Joe from Dallas, TX
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins

10 of 11 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

the rail broke on the meat drawer holder

I removed the shelf that hold's the rail's then one (1) screw that hold's the rail in place then I replaced the shelf. Simple & Easy!!

Parts Used:

Drawer Support Rail - Right Side

Geronimo from McAllen, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

10 of 12 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

FREEZER WAS COLD FRIDGE WARM

YOU TUBE VIDEO POINTED ME IN THE RIGHT DIRECTION. USED MULTI METER TO CHECK FOR VOLTAGE. NONE, REPLACED DEFROST HEATER. WORKS LIKE A CHARM, PART DELIVERED TO MY DOOR FOR LESS THAN $60.00, IN TWO DAYS FROM PARTSELECT. FIXED IT MYSELF FOR LESS THAN THE COST OF A SERVICE CALL.

Parts Used:

Defrost Heater

JEFF from OLIVET, MI
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers

10 of 12 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

ice was forming on inside of freezer. door not making complete seal.

door gasket just needed to be pulled out of edge around door and then the new one installed in the edge around freezer door.

Parts Used:

Freezer Door Gasket - Black

john from DALLAS, TX
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

9 of 10 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Freezer and refrigerator stopped cooling

The site offers a video for this part which worked perfectly. In addition to replacing the part, since the cardboard panel was off, we also cleaned all the dust off of the coils which someone recommended to do annually.

Parts Used: