Switch to Classic
Models > LDG9806AAE

LDG9806AAE Maytag Dryer - Overview

Sections of the LDG9806AAE

[Viewing 9 of 9]
Keep searches simple, eg. "belt" or "pump".
Drum Support Roller Kit – Part Number: 12001541
Drum Support Roller Kit
★★★★★
★★★★★
(168)
PartSelect #: PS1570070
Manufacturer #: 12001541
The drum support roller (Dryer Drum Support Roller, Drum Roller and Washer Assembly) holds the drum in the proper position while it spins on the support wheels. This part rotates on the roller shaft w...
$26.48
  In Stock
Dryer Cycling Thermostat – Part Number: WP3387134
Dryer Cycling Thermostat
★★★★★
★★★★★
(88)
PartSelect #: PS11741405
Manufacturer #: WP3387134
This thermostat (Dryer Operating Thermostat, Dryer Cycling Thermostat, Cycling Thermostat, Dryer Thermostat) is used to maintain a temperature of 155 degrees in the dryer drum. The internal bias heate...
$31.58
  In Stock
M Series New Style Coil Kit – Part Number: 279834
M Series New Style Coil Kit
★★★★★
★★★★★
(135)
PartSelect #: PS334310
Manufacturer #: 279834
When the igniter reaches a high enough temperature, these coils (Coil Valve, Dryer Gas Valve Coil Kit, Dryer Valve Coil Kit, Gas Valve Solenoid) work together to open the gas valve and allow the gas t...
$30.72
  In Stock
Tumbler and Motor Belt – Part Number: WPY312959
Tumbler and Motor Belt
★★★★★
★★★★★
(130)
PartSelect #: PS11757542
Manufacturer #: WPY312959
The tumbler and motor belt in your dryer allows the drum to spin during the drying cycle. At 100 inches in length, this dryer drum belt is 3/8 of an inch wide and has five ridges. The belt is black in...
$31.48
  In Stock
Front Glide Kit – Part Number: 306508
Front Glide Kit
★★★★★
★★★★★
(32)
PartSelect #: PS1804752
Manufacturer #: 306508
The front glide is located at the front of the dryer, the drum rides along it. If you hear a metal-on-metal noise when your dryer is running, your front glide may be worn out and require replacing. Th...
$14.80
  In Stock
Roller Shaft – Part Number: WP6-3129480
Roller Shaft
★★★★★
★★★★★
(3)
PartSelect #: PS11743031
Manufacturer #: WP6-3129480
This roller shaft is also known as a support roller shaft or a drum roller axle, and is a part for your dryer. The function of this piece is to act as the axle for the drum roller; it provides a place...
$11.24
  In Stock
Blower Wheel with Clamp – Part Number: Y303836
Blower Wheel with Clamp
★★★★★
★★★★★
(76)
PartSelect #: PS2200270
Manufacturer #: Y303836
This comes with a metallic hub clamp to hold it firmly in place. The blower wheel with clamp is part of your dryer assembly. You will find this part attached to the drive motor shaft, which disperses ...
$22.20
  In Stock
Retaining Ring – Part Number: WP9703438
Retaining Ring
★★★★★
★★★★★
(3)
PartSelect #: PS11746909
Manufacturer #: WP9703438
This part is a retaining ring, sometimes called a retaining clip, that holds the drum support roller onto the shaft of a dryer. It is made entirely of metal and measures less than an inch in diameter....
$6.67
  In Stock
Timer Dial Skirt – Part Number: WP33001621
Timer Dial Skirt
★★★★★
★★★★★
(61)
PartSelect #: PS11741055
Manufacturer #: WP33001621
This timer dial skirt is just over three inches in diameter. It is white in color and is made entirely of plastic. This skirt has a gray indicator triangle.
$23.60
  In Stock
Lint Filter – Part Number: WP33002970
Lint Filter
★★★★★
★★★★★
(58)
PartSelect #: PS11741140
Manufacturer #: WP33002970
This is a replacement lint filter for your dryer. Replacing this part is easy as it requires no disassembly of the unit. Make sure to clean the filter after every use of your dryer, and check the filt...
$20.52
  In Stock

Questions And Answers for LDG9806AAE

Be the first to ask our experts a question about this model!

Common Symptoms of the LDG9806AAE

[Viewing 12 of 12]
Noisy
Fixed by
these parts
Show All
No heat or not enough heat
Fixed by
these parts
Show All
Will not tumble
Fixed by
these parts
Show All
Will Not Start
Fixed by
these parts
Show All
Takes too long to dry
Fixed by
these parts
Show All
Timer will not advance
Fixed by
these parts
Show All
Shuts off too soon
Fixed by
these parts
Show All
Will not shut off
Fixed by
these parts
Show All
Door won’t close
Fixed by
these parts
Show All
Too hot
Fixed by
these parts
Show All
Marks left on clothes
Fixed by
these parts
Show All
Touchpad does not respond
Fixed by
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The blower fan (nylon) stripped off the motor shaft (steel)
Removed the front cover (screws on bottom 0f face)...removed blower cover....spring pliers to remove and install blower fan. the rest of the time was spent cleaning the inside of the shell as well as the vent. Reassembled and dryer runs better than it has for many years.
Parts Used:
Blower Wheel with Clamp
  • Stephen from Lafayette, IN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers
553 of 554 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
dryer squeeking
removed front panel,lifted top, removed drum and drive belt,remove old rollers and acc and instlled new and reinstalled dryer parts.
Parts Used:
Roller Shaft Roller Shaft Hex Nut Drum Roller Shaft Washer Drum Support Roller Kit Retaining Ring
  • gerald from park city, MT
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Pliers, Screw drivers, Socket set, Wrench set
500 of 530 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Belt broke on old machine.
1. Removed front of machine (2 screws at the bottom).
2. Removed 4 screws from inside the dryer, to take off the blower housing.
3. Removed 4 screws and took out the large metal piece which supports the drum at the front. Removed the drum.
4. Replaced the two rollers that support the drum in the rear. Cleaned the pins they run on, and oiled very lightly. Also replaced the idler roller. I was surpirsed to see that these rollers use plain bearings, not ball bearings.
5. On the front support piece, drilled out the rivets for the glides, and replaced the worn out glides with new parts. Applied a little glue (3M weatherstrip adhesive) to the cork pieces, to glue them to the metal. Attached the plastic pieces over the cork pieces, and riveted in place using rivets that came with the glide kits.
6. Replaced front and rear felt seals. This was not as tricky as I expected it to be. They were held in by metal tabs. Glued the ends where they came together.
7. Replaced the felt blower seal. Glued to the blower housing.
8. Reinstalled the drum, installed new belt, which came with good instructions (luckily).
9. Reassembled front support piece and the front of the cabinet.

I also cleaned the lint from the cabinet and from the vent hose.

In general, the job went without a hitch, and the machine probably has quite a few years left, despite the fact that it's 18 years old. This gives me a good feeling.

I'd say this would be challenging, though, for someone who is not pretty experienced with machinery repair. Also, the cost of the parts was significant enough that it would not have been unreasonable to have opted for a new machine.
Parts Used:
Tumbler and Motor Belt Dryer Blower Housing Seal Idler Pulley Wheel Front or Rear Drum Felt Seal Front Glide Kit Drum Support Roller Kit
  • John from Charlottesville, VA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers
520 of 637 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!