LCRE655 Maytag Range - Instructions

Removed the oven door, removed old burned element, installed new element. Turned CB back on and tested oven. Reinstalled oven door. Straight forward and easy to follow directions with new element.Local appliance part house said the element was no longer available. Thanks to you I did not need a new oven. Very easy replacement job with normal tools.Thanks

Take off the old knobs & put on the new knobs. They work & look great. Based on the age of the oven in the older home I purchased I was very concerned I would be unable to replace, but you made this very easy to do. Thank you.

The knobs were so worn my wife couldn't make the proper setting. The new knobs I ordered arrived so fast I couldn't believe it! They are beautiful and my wife is happy!!

Unplug stove from outlet!! Removed screws (Phillips head) from prior element and pulled out enough to slip of the red and white wires. Keep in mind which side which is on and take old element out of oven. Put new element in and attach wires back on the same sides. Push back in and use screwdriver (Phillips head) to lift insulation to push wires and element prongs back. Put screws back in, close oven door and plug stove back in. Tested and works great!

The element appeared to have been damaged. I replaced the element with ease. However, I still have the same problem. The oven does not heat up to the set temperature. Information from the part select website is that it is more likely the long oven sensor. I ordered one and will provide the results after I have this sensor replaced with a new one.

Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

burner replaced

Compressed the springs and removed the damaged switch, then changed the wiring over to the new switch and press into place, worked fine.

My oven temperature knob has been discontinued by manufacturer Maytag. I looked thru your vast list of knobs and found one that looked excately like my knob dial. The knob is a two piece design. My shafts that the knobs slide onto are different than the one I selected but since it was a two piece knob, I was able to use the center part of my knob that fit the shaft of my oven and use the new dial face. I spayed it with a clear lacqure top coat to protect the dial face from the numbers and letters disappearing as the old on did. Worked perfectly. Happy wife, happy life. I will give your customer service an A plus as one of the dial knobs that came in a not so well protected package was bent. They agreed to send out another right away which they did. I would definately purchase from you again. Thanks so much

Just pulled to old knobs off and slipped the new ones on, so very easy to repair and now my oven looks like new. Thanks for all your help, all I needed was the model number to get the right part.

After we got the part in the mail my husband put it on and shortened the wires and put new plugs on the ends of the wires and we had to get a new plug put it on and it was fixed.

The Burner Control Switch - 250V Part Number: PS2089409 that this site recommended was the right part for this older range. Had to remove screws to pull out the front panel with knobs, but it only pulls out a couple inches due to wires so it is tight to remove old switch. The five tabs are not in same spot so go by the labels and the wire lugs fit just fine, and the knob snapped right on and works great. Thank You!

My son-in-law installed the new element. First turn off the electricity and remove oven door. Then unscrew all connections to the element.The back electrical wires come out from the top back oven. The bracket screw faces the oven and the electrical wires are so short there is very little room for a screw driver (get the shortest one you can find..abt as big as your thumb if possible).Once that was out the element came out with no problems.Then it's just reversing the step. Again, that back electical bracket is difficult to get to for install. Also, the new screws in our kit were Philips, but the old ones were flat so check those out before turning off the oven light.

I UNPLUGGED STOVE, removed panel covering the controls, removed the knob on front and the two screws there that hold the control in, inserted new control and replaced the two screws on the front that hold it onto the stove, used needle nosed pliers to unplug one connection at a time from the old control and onto the new control in the back. When I had all connections plugged onto the new control I re-installed the panel cover with a screwdriver, plugged the stove back in, and the burner is now working good as new!