LATH100ATV Hoover Washer - Instructions

Replaced the hose. two clamps and retainers. very basic repair

Unhooked the macine pulled out for easy access .removed drive belt rear cover plate ,vaccumed remaining water out thru drain hose with wet and dry vac. Removed hose clamps and hoses .removed the three hex screws holding the pump to the base plate. The removed the old pump , Installed the new pump hoses access plate and belt . Hooked the machine up . Worked perfect.











the

I removed the cover on the back of the machine, detatched the 2 hoses and removed the 3 screws holding in the Vertical Style Pump - with pulley. These screws are 10 mm nut-driver. The cover if I remember correctly was a standard rather than metric so make sure you have both available.

Screwed new part in, re-attached hoses and replaced cover. The last step requires strength to hold the machine up and re-configure the belt. This is best accomplished by looping it onto the tub and the pump first, the using the tub pulley to maneuver the belt onto the motor.

Only discouragement was that it took 8 days to receive the part as the first shipment was not the correct part at the fault of the distrutor.

first i removed the front panel unclamped the hoses unscrewed the 3 screws that hold it in pulled it out, opened the new one and actually dropped it in and it fell into place with the holes lining up inserted the screws and hose clamps and reinstalled the belt which fell off when the old pump was removed, put the front back on and gave it a test then let the wife do a load of wash it worked like new

I raised the top of the washing machine per video instructions, removed the screws, replaced broken hinges with the new ones. It was simple as that.

I first changed the belt which helped but it still sounded like it was going to take off through the roof.....I did the pulley and bearing kit in hopes that it would do some good....it went really smoothly with no issues however it did not solve the problem....so it is working and I am going to just ride it out until it quits....thanks

I used the putty knife to release the spring clips on the machine lid. They are about 3" in from the side of the machine. Then I lifted the top of the washer up holding the lid in place. I then used a screw driver (torx) to remove the hinge from the bottom of the washer top. The lid should come right off. Then I the removed the broken hinge pins from the back of the lid with a screwdriver and replaced with the new parts. There is a little tab that the pin fits in the lid to assure you have the pin installed correctly. Then I slid the hinge back on the pin and reversed the process reinstalling the hinges and closing the top of the machine over the spring clips and your done. Very easy repair that I completed in less than 15 minutes.

Easy repair - with the use of a phillips screwdriver, simply remove the old device and replace with the new

Lift the top of the washer so you can access the screws that hold the hinges. Replace the hinges,and close the washer top. This is the sescond time we have had to replace the hinges.

This lid and hinges are very poorly designed. Instead of opening to the side, it opens straight back. That means when the hinges wear out (and they do because they are plastic), you have to push the lid all the way back to stay open. When you push it all the way back, it hits the control knob and turns off the water.

If you are like me, I like to turn the water on and add the soap so it can dissolve before I add the clothes. It is really irritating when you open the lid and the only way for it to stay open is to push it all the way back and the water shuts off. And if you don't push it all the way back, it slams and scares the bejeebers out of you or slams on your fingers.

Turned water off,tilted unit forward,removed lower rear cover,removed belt,laid towels around ,removed inlet hose and exit hose off pump,removed 3 screws holding pump,removed pump and installed new one,reversed order of disassemble, has been running great ever since.

I unscrewed the old lid switch and screwed on the new switch in seriously 2 minutes!

short drive, 90 degree, "star" driver. push tub to side and back to reach lower part of old hinge, remove single screw. (careful not to drop it into the "mechanics" of the tub.) repeat for the other side. remove parts from lid. reassemble new parts onto lid, along with lower hinge parts. secure the lower hinge to door part(s) with masking tape to hold in place. hold lid in place over lower hinge screw holes and start screws by hand. snug up the screws and your done! the 'STAR" screws may be relpaced with similar "phillips" so you wont have to scrounge for a "star" driver the next time.

Reverse the process to install new pump
Unplug the machine
Place pad on floor to protect the machine from scratches
Lay front of machine on floor
Remove back cover (10 screws)
Disconnect 2 hoses
Remove 4 screws which secure pump to bottom frame
Remove belt
Remove pump

Reverse the process to install a new pump

Your web sites intuitive design makes it easy to navigate and the customer service person was knowledgeable, easy to understand and professional.

The part arrived via UPS in 3 days. It was double boxed (well packaged) and most importantly, it was the correct part.

This was is 1st time we used your server but it won’t be the last!

Kudos to the entire staff and please…keep up the good work.

Sincerely,

Lon Thomas

Unscrewed the front panel. Then took pump out & put new one in. . . . . Thank you part select. Com. . . Super fast shipping. . .

I followed the feed back in the forum from a previous repair. I popped open the top of the Washing and propped it open @ approx. 70 degrees,moved the Tub out of the way and used a small Phillips Scwdrvr to remove the broken part, installing the new parts was a snap, I took the time to use a Q-Tip and petroleum jelly to coat the pin and hinge making it easier and less binding when opening the lid.