Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Washer made grinding noise then stopped working.
First I tipped the washing machine onto its front. I removed the belt on the bottom of the machine. Then I removed the screws that held the cover in place on the back of the machine. Next I removed the two hoses that were connected to the vertical pump using pliers to pinch the clamps. I then removed three screws that held the vertical pump in place. I took the new verticle pump with pulley and mounted it to the washer and putting the washer machine back together using the previous steps in reverse order.
Removed excess water,removed hoses,tiped back washer,removed belt,removed pulley and bearing. Removed 3 screws and replaced with 3 longer screws in the stator,then removed 3 shorter screws. Then loosen very slowly each of longer screws to relieve pressure from the brake spring. Once loose,pulled out brake rotor. Replaced with new parts. Works like new.
1. Unplug power cord. 2. Move washer away from the wall to get access to the back of the control panel. 3. Remove 5 screws from the back panel cover with 1/4" driver, & remove cover. 4. Pull the Water Level Switch knob out from the front control panel. 5. Use pliers to slide away the retaining clip holding the clear rubber tube to the water level switch, & separate the tube from the switch. 6. Use 1/4" driver to remove 2 screws holding the switch, & remove the switch. 7. Remove the electrical wires 8. Install new switch in reverse order.
When you are testing out the washer afterward & your spouse said still not fixed because she thought the water level is too high when the water is still running? Wait a little while longer, the water should stop. She is just not used to see it filled without a load of laundry in it.
I felt extremely confident when purchasing the part because I say three diagrams which clearly showed I was ordering the correct part. 0. Drain all of the water out of the machine. 1. Remove the rear panel from the washer. 2. Use the pliers to disconnect the hoses from the pump. 3. Remove the three screwa from the old pump. 4. Support the washer with the block then take the belt off pulley. 5. Remove old pump. 6. put new pump in place then reconnect the pulley, you can remove the block.. 7. Install the three screws for the pump after you tighten it up by placing the pump over ther correct screw holes.. 8. Reconnect the two hoses using the clamps you removed. 9. Secure the rear panel and screw in place. 10. Wash clothes. EASY FIX!!!
Washer was shaking and noisy, wasn't spining fast and overall running poor.
The hardest part of this is the springs. The best way to disconnect and reconnect was to tilt the tub towards the spring I was trying to work on (thus putting less tension on the spring and cutting down the distance). I took a large boot and jammed it into the oposite side wall to hold it in a tilted position before I disconnected the spring and then redid that to reconnect using a vice grip wrench. I replaced all three things, snubber, brake roto and stator and it went back together very easily. The key on the pully shaft was hard to reattach but there was a trick to that as well. The shaft has to move up slightly to slide ring on so you need to have something under the tub to help raise it. After that was back together it was 15 mins. to finish and now the washer is running like new.
Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
13 of 15 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Cover of washing machine wouldn't stay open, it fell on my wife's hand.
This is a very simple repair, I opened the top of the washer by inserting a screwdriver between the top and the washer cabinet. There are 2 clips on the front of washer, locate and push in to release top. Lift top with lid attached and remove the 2 screws holding the lid to the top of washer. Remove lid and replace hinge pin and hinge. Replace lid, close top , all done. Total time about 15 minutes or so. Now the lid will stay up and not fall on someone.
during wash cycle, water poured out of bottom of washer
first we looked at schematics on your web site to see what we thought was wrong and if we felt we could do ourselves. It appeared to be seals and gaskets, so we went for it and carefully took the washer apart. We ordered the parts, cleaned the parts we had such as the tub, and were all ready to put back together when the parts arrived. Again, using your pictures, we reasselbled and when we tested, it worked better than it had been in a long time. And we saved a large repair bill!
Removed the front panel, Removed the belt from pump in the back of machine. Removed the pump from the back of machine, Put the pump in reconnected the belt, Replaced all the screws. My husband did the repair work in a matter of 45 minutes. Machine works fine now. The part came when I was told it would. I am very pleased with your service.
Lid switch had deteriated over time and no longer made contact
removed the screw holding the actuator, ordered the new part and replaced it when it arrived. Shipping was really fast and I even received it one day early.
First push inner tub to left rear, all the way, and unscrew hinge from inside of tub. repeat same on right side. lift cover off and unscrew other half of hinge off cover, both sides.reverse procedures and your done. Note: always replace both hinge's new while you have it apart.
For safety I Unplugged the machine Tipped machine back and removed the belt. Rotated the motor by hand and all is well there. Rotated the water pump by hand and a grinding sound appeared. I Let the machine down . Using a hard object , 1/16th of an inch thick, I slide it between the front edge of the lid and the front panel unlocking the clips ( one on the right side and one on the left side ) holding the lid down. I then tipped the lid up and removed the 2 screws holding the front panel on. Lifted the front panel off of the clips on the bottom end of panel. Using a nut driver I removed the 3 bolts holding the pump to the frame. Then with a pliers I removed the clips holding the 2 hoses. With a pan to catch the water I removed the hoses and drained them into the pan. I then took my machine model number and went to the internet in search of a new water pump. After checking several sites with no success, I come upon the site for PartSelect.Com. With the excellent search method on the site I was able to quickly find the part I needed. I placed my order (10pm) on a Tuesday night and a short time later I received an email letting me know they had my order. On Wednesday I received an email letting me know they had shipped my order. On Friday the order had arrived. I removed the new pump from the box and inspected it . Every thing looks great. I placed the pump into its mount on machine and bolted it down. Attached the 2 hoses, put the front panel back on and tipped the top down into place. Pushed machine into place, plugged it in and fired it up. I now have a quiet running machine again. Thank You to PartSelect.com for the quick response to my
tip washer up on wooden blocks.remove drive belt.remove "E" clip from tub drive pulley and remove all the parts.Install new parts in kit as per instructions.machine works great!
Removed the screw from the side of the lid of the washer. Took off the old Lid Switch Actuator and screwed in the new one. Took a little elbow grease because the old screw was tight but no longer than 15 minutes tops.
After replacing the tub to pump hose, I adjusted the feet on the washer. Apparently, the main pulley sits so low on these washers that it ground into the floor and stripped out the thrust bearing. I ordered the new thrust bearing clip and put it in the evening I received it. The instructions it came with were very helpful and it was simple to reassemble. Up until the last piece - the retaining clip. The majority of the repair time was spent replacing that clip. If there is a tool that makes the job easier, I didn't have it. I finally got it on with two flathead screwdrivers prying the shaft out while I wedged one corner of the clip in the groove.
I removed the part that was still attached to the washer and installed the new flume. It took less than five minutes and a repair that would have cost over $85 cost less than $10 and I am no plumber!