KUCS181B0 KitchenAid Trash Compactor - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Door latch catch broke
4 of 7 people
found this instruction helpful.
-
Raymond from Washington, DC
- Really Easy
- Less than 15 mins
-
Pliers
I squeezed the latch catch with a pair of pliers and pushed it in the catch hole. But that was the final repair. There were two "repairs" before that. First, we used two commercial grade rolls of wide plastic tape to tape the dryer door shut each time we used it, for a year, until we ran out of tape. Second, we positioned a chest of dra
... Read more
wers in front of the dryer and wedged a 1" x 4" against the door. Very effective. Then I broke down and ordered the $3 catch.
Read less
Was this helpful?
Thank you for voting!
Dryer door latch broke and door wouldn’t stay shut.
2 of 2 people
found this instruction helpful.
-
Susan from WARREN, NJ
- Very Easy
- Less than 15 mins
-
Screw drivers
Jimmied out the latch using two screw drivers to get under the edges. Pushed the new piece in. Voila! Took 2 minutes for what my repair man told me would cost about $200 to fix. Unbelievable!!( I first watched some YouTube videos to get the idea )
Was this helpful?
Thank you for voting!
Broken Drive Belt On The Ram
3 of 6 people
found this instruction helpful.
-
steven from shebogan, WI
- A Bit Difficult
- 15 - 30 mins
-
Screw drivers, Socket set
I Removed The Back Panel To Get At The Top Panel Which In Turn I Got To Top Plate To Access The Gear Drive, The Ram Was In The Down Position So I Used a Socket And Rachet To Crank The Ram Up By Hand, I Then Loosened The Plastic Gear Mount To Move The Gear Forward To Attach The New Belt, Then Reversed The Procedure putting The Campactor In
... Read more
operating Condition And It Work's Great
Read less
Was this helpful?
Thank you for voting!
Dryer door wouldn't catch and stay shut
1 person
found this instruction helpful.
-
Melody from TEXARKANA, TX
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
I take the screws out of the door, I removed the catch from behind inside the dryer door, I slid the new catch in the door and snapped it in place. After getting a new catch in the door I put the door back together and put the screws in. Easy repair
Was this helpful?
Thank you for voting!
door would stay closed
1 person
found this instruction helpful.
-
william from KILLEEN, TX
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
just replaced parys
Was this helpful?
Thank you for voting!
broken door catch
1 person
found this instruction helpful.
-
Susan from HUDSON, MA
- Very Easy
- Less than 15 mins
-
Pliers, Screw drivers
I followed your short video and found it very easy to do
Was this helpful?
Thank you for voting!
broken door catch
1 person
found this instruction helpful.
-
Frank from ENDICOTT, NY
- Very Easy
- Less than 15 mins
-
Pliers, Screw drivers
Took 3 screws out used the putty knife to pry the door a part then used the pliers to remove the old door catch and then sapped the new one and put the door back together and I was was done in less than 10 min.
Was this helpful?
Thank you for voting!
latch was broke
1 person
found this instruction helpful.
-
Rick from SAN DIEGO, CA
- Really Easy
- Less than 15 mins
-
Screw drivers
just followed the video directions, worked perfectly thanks
Was this helpful?
Thank you for voting!
dryer would not run because catch did not hold tight enough to press door switch.
1 person
found this instruction helpful.
-
j from TAZEWELL, TN
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
removed screws that held the door face to gain access to catch replaced catch reassembled door tried dryer works great!
Was this helpful?
Thank you for voting!
Door catch was cracked
1 person
found this instruction helpful.
-
Tammy from glenford, OH
- Very Easy
- Less than 15 mins
Incredibly simple! You just pop the other plastic catch out with a butter knife and pop the other on in. This is the second time I have done this over the last 4 years or so.
Was this helpful?
Thank you for voting!
Door would not stay closed - so dryer kept shutting off
1 person
found this instruction helpful.
-
Barbara from NORTH EASTON, MA
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
Followed Youtube video - quick & easy
Was this helpful?
Thank you for voting!
Broken dryer door catch
1 person
found this instruction helpful.
-
Kenneth from UPPR MARLBORO, MD
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
Followed the video instructions which were comprehensive, easily understood, and prefaced with a listing of necessary tools. Completely satisfied with parts and supplementary information.
Was this helpful?
Thank you for voting!
Dryer door would not stay closed
1 person
found this instruction helpful.
-
Gregg from St. Augustine, FL
- Really Easy
- Less than 15 mins
-
Screw drivers
After removing front door panel (2 screws) I removed the old latch catch and replace with the new part. 4 minutes later, the door was back together, the dryer was running and the door was staying closed.
Was this helpful?
Thank you for voting!
The door whould not close enough for the dryer to work.
1 person
found this instruction helpful.
-
Frank from Union Beach, NJ
- Really Easy
- Less than 15 mins
-
Screw drivers
Got my parts very quickly.
Popped out the old door latch with a screw driver and pressed in the new one.
Very simple.
Thanks Parts Select.
Popped out the old door latch with a screw driver and pressed in the new one.
Very simple.
Thanks Parts Select.
Was this helpful?
Thank you for voting!
dryer door won't stay shut
2 of 4 people
found this instruction helpful.
-
Diana from Canfield, OH
- Easy
- Less than 15 mins
-
Pliers, Screw drivers, Wrench (Adjustable)
I replaced the male end first hoping that a change in the female part would not be needed. Unfortunately no. I used needle nosed pliers to pry the male part out and pushed the new part in. The female part of the door catch was more difficult. I didn't do it in "textbook" form, but got the job done with pliers and a screwdriver. Worth ever
... Read more
y penny to fix correctly instead of rigging it. Do it!
Read less
Was this helpful?
Thank you for voting!