KSRS25FGBT02 KitchenAid Refrigerator - Instructions

It was really easy to do. The water filter is in the front of the refrigerator. Less than 30 seconds. I am very happy with PartSelect. I bought parts for my dryer too. New lint filter, timer knob and door handle. Parts arrive immediately. I am sure I will be back to PartSelect.com.

Removed face plate, disconnected wires, removed and replaced micro switch and control bracket.

I first removed the ice bin from freezer. There were four nut screws on back of ice bin cover that I removed with a screw driver, giving me access to the deflector. The deflector has two prongs that attach it securely to the ice bin, I used a phylips head screw driver to release the prongs from the deflector. I installed the new deflector by placing it through the bottom portion of deflector area, using the phyllips screw driver I engaged the prongs of the deflector into slots on ice bin. There was a hook on the back side of the deflector that went over a metal rod that controls the ice cube release. Then replace front cover of ice bin with the four nut screws and returned it to the ice maker location.

It was easy, I followed the instructions on the paper and it went well.

I replaced the control bracket, which has mounts for the switches used to activate the ice and water dispensers. The water switch mount was broken, so the switch would not activate. It was great that I could find this part (the control bracket) on PartSelect's site.

If the person doing the repair has a little patience, then he/she will be rewarded!:

The first step is to pry off the front panel: I pried off the panel at the bottom. It will pop off, but takes a little effort. I used a couple of screwdrivers to pull it up at a couple of spots at the same time. Once the bottom pops out, then I pulled straight up on the panel. (If you try to pop out the panel at the top, you will damage it, so make sure to pop it out at the bottom.)

Next, disconnect the wiring that goes to the panel, and put the panel aside.

I then took a digital picture of the arrangement of wires and switches on the control bracket.

I disconnected any wires going from the inner part of the refrigerator to the control bracket, and then unscrewed the control bracket.

After removing the old control bracket, I carefully noted how the two switches (one for ice, one for water) mount into it. I removed these switches and put them into the new control bracket.

I then remounted the control bracket into the refrigerator, screwing it into place. I used the digital picture that I had taken earlier to make sure that I knew how to reconnect all of the wires.

I plugged the the remaining wires to the front panel, and then snapped the front panel back into place on the refrigerator door.

I was done!

Followed instructions supplied. It was relatively easy and the parts fit exactly right. Sears wanted twice as much for the part and service would have charged me another $100 to come to my home. I saved over $100 doing the project myself.

Removal of the old assembly went quickly once I
understood about the "push and release" tubing
connectors. The exception was the connection from the water inlet assembly to the water filter which uses a different diameter connection at the inlet end, and would not "push and release".
So to install the new valves, I simply by passed
the old inlet assembly and used the extra push
splicer furnished in the kit for the water inlet to the
filter. All the other connections were easy push ins.
Next time will be 1/2 hour maximum!

The CAUSE of the LEAK were the O-rings on the water filter itself. My son followed others suggestions on how to detach the water hose from the filter housing, advise was helpful. After replacing the water filter housing, helpful, and inflow water tube the leak was still there. So my son then inspected the water filter and replaced. Water filter light was still green so we did not think it needed attention.

1. shutoff water
2. removed 3 screws holding old ice maker. A small nut or screw driver is needed to get into a somewhat tight area
3. detached electrical connector
4. cut indicated area for water inlet to lie in
4. attached new electrical connector (no splicing needed)
5. attached new ice maker with 3 screws
6. put on water

Remove the cover plate from the bottom. Use care and patience when performing this step. It takes longer to remove the cover plate than replacing all of the parts involved. Slide off each switch, unplug electrical connectors and trust me when I tell you that you can figure out the rest. E Z, E Z, E Z!!!!!

my order was processed and received withn 3 days. Replacing the parts on my kitchenaid refrigerator was straight forward, since the design was made for quick removal for cleaning of parts, with no tools required.
My only recomendation to KitchenAid would be possibly design the weak points a little stronger so they do not break in the first place.

Unscrewed the old one (Half turn) and screwed in the new one.

First I installed a defrost timer, (the old timer had burnt out contacts in it) It seemed to work for a few days, then went back to not comng out of defrost cycle, I then installed a defrost thermostat. It seems to be working better than before. I found out that maybe I wasn't running it cold enough. So I turned it up colder. Now it works ok for 2 - 3 days, then I check the Temp in the freezer and its up to 6o. So I manually reset the timer and it works for 2 - 3 days. Don't know what to do now to fix it.

I removed the screws on the upper hinge and removed the door. I removed the lower cam in about 2 minutes and had it replaced. The upper cam was a tight fit in the door and I resorted to vise-grips to remove it. Total time to replace cams and put the door back on was 30 minutes. This saved me $100.
Thanks

Pulled cardboard cover off back of ref to access the compressor compartment. Unplugged appliance, and pull the start device and overload off of compressor. Replaced both parts received from Partselect.com. Refrigerator works great now.