KND2049 (4L44A) Admiral Refrigerator - Instructions

Looked up on the internet and found the part. The Kenmore washing mahine is 20 years old. I have never had any repairs. The part came in 3 days and I merely followed the old threads on the screw and it washing machine works now!
I'm 77.
THANK YOU!

I removed the 2 crisper drawers and the glass shelf directly above the Pantry Drawer. Removed the Pantry Drawer and Pantry Drawer cover so you have easy access to the Right-Hand End Cap. On the right-hand End Cap, there are 2 screws which hold the End Cap in place, use a 1/4 inch driver to unscrew the screws from the front of the cabinet on the End Cap and half-way in of the cabinet, leave the screws in their holes in the End Cap. Lift gently to get off a small plastic pin, and move the End Cap away from the Cabinet. You don't need to completely pull the End Cap out of the cabinet, it'll move more like a door opening. Place 2 washers on each screw and gently put the End Cap back into place, being careful NOT to jostle too much so the washers don't fall off the screws. You will need to gently lift the End Cap back in to place over the plastic pin. Hand-tighten the screws back into place with the 1/4 in driver. Remount the Pantry Drawer on the sliders. When you go to install the Pantry Drawer Cover, you will need to gently push on one of the pins to get the cover back into place. Put glass and crisper drawers back into place.

Test by gently pulling on the Pantry Drawer. If properly mounted, the pins will extend fully into the Cover and will keep it secure when opening the Pantry Drawer.

I was happy to find this place. Sears was out of stock on this part. PartSelect was $5 cheaper than Sears and sent it the next day.

Part is better, inside is metal not plastic, won't break again.

Screwed off remains of broken plastic and screwed on new knob. Easy as pie!

I tilted the unit back enough to scew the new legs into the threaded holes.

My wife wanted to call a repairman from the store. Instead, I ordered from PartSelect, replaced it in seconds, and saved over $100, all for about $20 - you can't beat that!

Unplug fridge, unpluged fan motor from plug socket, removed bracket screws, removed fan retainer clip from shaft. removed screws holding fan to bracket

First I replaced the broken plastic control knob with the better die cast knob.
Pried the cap from the top of agitator assembly ..after first removing the softener dispenser.
Used socket with extender to remove visible retaining bolt. Pulled out plastic column and old dog bone ratchet assembly. Removed and replaced bottom spacer ( this had busted tabs and caused noise during agitation), greased all appropriate points with silicon grease..lithium would have been better...ordered wrong agitator so put old undamaged one back with new dogs which fit. Snugged down bolt..runs like new machine again.

I had already disassembled the part. All I had to do was thread the new part. My wife thinks I'm a genius. I guess I am, I ordered the right part and it was delivered in a timely manner.

I removed 7 screws hold the heavy cardboard cover on the rear of the fridge. The dificult part was taking the screws that hold the 3 fan motor braces on the fan out. After that it was a matter of making the wire conections and putting it back in. I did not have enough room to laydown to do the work, If i had it would have been a lot easier to see the screws that had to be removed. All in all an easy job, and the part was a perfect fit.

removed old and instaslled new. biggest problem was getting to one of the screws.

Turned refrigerator and freezer controls to off, removed icemaker bin, unplugged icemaker plug and removed two screws holding icemaker in place and removed icemaker. removed screws holding auger motor and freezer compartment light plate, unplugged and set aside. Remover screws holding freezer coil cover in place and removed cover. Allowed coils to defrost completely and then removed screws that hold the two defrost heater coil mounting plates in place, unplugged the two wires that connect the defrost heater coils to the connector block that is located above the freezer coil. Remove the entire defrost heater by working the connecting wires out from along side the freezer coil. Remove the clips that hold the old defrost heater elements to the mounting plates. Install new heating elements into the two mounting plates with the clips. Reinstall the two mounting plates to brackets on freezer coil and reinstall connecting wiring up to connector block and reconnect them. Reinstall freezer coil cover, icemaker auger motor and freezer compartment light plate, and icemaker and bin to complete job. Due to the confined space in the freezer compartment, reinstalling the freezer coil cover and light plate was difficult as I could only use one arm at a time resulting in many dropped screws.

it went good

remove all tray,remove back panel,cut out out old heater adn replace with new heatger,refitted back panel and alll tray.

Ordered new fan motor on line took out old motor and replaced with new one

Partition between Freezer and Fridge was running very hot. (Warm is normal). Oiling fan did not work. The only problems encountered in the replacement were getting fan out and in through coolant lines, cut plug off to accomodate generic fan wiring, getting the screws back in without cooking your hand on a hot compressor. Unit works great!