KGST307BAL1 KitchenAid Range - Instructions

Took the back off the stove, removed 2 screws, unclipped the bad sensor, clipped the new one on, put the screws back in and the back of the stove back on and that was it - 10 minutes

Loosen 2 screws and put new part in and tighten 2 screws. After putting in new sensor stove gave me another code had new part in 5 min and part select would not take my part back.

The old part, including lightbulb and socket, had corroded into place, and the glass light cover was stuck to the socket. I used a dead blow hammer and a dowel just under the diameter of the hole to tap on the back side of the socket to loosen it and get it out. The metal tabs on the old socket were folded back to make it fit better (?), which made it harder to remove. Lots of muscling of the part to get it out. Easy to install new part once old one was out of the way. An experienced person would have removed the old part and installed the new in no time.

I trouble shot and traced out to electrical short in face panel and found burnt wires. I've been a licensed electrician for years and it takes alot of comon sense to trouble shoot and find problem. I found schetch-matic of appliance and searched computor and found partselect.com and tried it. It wasnt no time and the part was at my door. Thank you partselect and i would use them again in the future. billy

Only one screwdriver needed for this simple repair. Unfortunately for me it did not repair my oven and a new code on the oven indicated a bigger problem with computer board.
Part Select was great to work with and accepted a return and promptly refunded me for the part.
Thank you!

DISCONNECTED POWER AND GAS TO THE RANGE. REMOVED 6 SCREWS FROM REAR OF THE RANGE. REMOVED THE 2 SCREWS HOLDING THE TEMPERATURE SENSOR IN PLACE. DISCONNECTED THE LEAD FOR THE SENSOR. INSTALLED NEW SENSOR IN REVERSE ORDER. OVEN WORKING PROPERLY NOW.

Remove old knobs and replace with new ones!

I unscrewed the igniter from the top of the oven, and removed the back panel of the stove. I had a friend in the back while I jiggled the two wires to see which ones they where. Then I had to use two pliers to pull the connectors apart. I tied a string to the two wires and pulled them out through the oven and left the string and tied the new wires to the string and pulled the new wires through the back of the stove, and replaced the back and screws.

TURN OFF THE GAS SUPPLY & POWER TO THE STOVE. Disconnect the gas line & power source to the stove. Remove the complete counter top stove and place it upside down on a flat surface to enable you to remove all the surrounding small screws with a nut driver, then separate the bottom from the top accessing the retaining ring holding the ceramic electronic Ignition in place, remove the electric wire from the the old igniter. The most difficult part of the job was removing the retaining ring and installing the new ring.Job successfully completed.

I have KitchenAid convection oven that is about ten years old . The hinge on the left hand side broke so I had to replace it. It took me about 2 hours to get the job done because I cleaned the door as I went . The change out while fairly strait forward did take some time . A lot longer the some of the people said .

Replaced damaged drawer roller: easy peasy!

The nylon roller was very easy to install. Although rather pricey for what the part was, it was shipped immediately and got the job done. Took all of 5 minutes to do. I wish all my repair jobs were that easy.

Pop old one out and new one in

My son had first removed the 2 screws to disconnect the damaged element. He then removed the element
by pulling it out and disconnected the wires.

I was si grateful when he was able to connect the new igniter so we could have cookies for Christmas...thank you for your very prompt delivery of the element and the ease to reconnect it.

Ordering the part online was easy. It arrived in a timely manner. I found a terrific video online showing how to install the terminal. It was so easy. Thank you for the great instructional video.