KFXS25RYBL1 KitchenAid Refrigerator - Instructions

Put new one on matching the sctew feet and design of the grill

Everything went as planned except the cold temperature (freezer door switch located inside freezer) made deflection of the switch locking tab difficult to remove. Letting the switch warm up was not an option.

Took the old one off put the new part on. Took 1/2 hour

When you open the box, have flat place prepared so you can lay the seal down to allow it time to relax. Only handle the seal by the corners. Lay it flat. I used a hair dryer to remove the creases during its time in the box. Keep the hair dryer moving, don't rush this step, take your time and allow the seal to relax on its own. Once it's completely relaxed. Remove the old seal by starting at the corners. No tools needed just keep working around the entire seal. Inspect the seal chanel and clean as needed. Pick up the new seal by the corners and press in place with your fingers, starting at the corners. I found doing the top first then the sides, leaving the bottom to last worked for me. Hope this helps.

Checked Video online. Had to remove the 2 snap on track/gear covers. Pry out the gear with screwdriver and the gear bearing unit. Align the flat side of the bearing unit and snap in. Position the cut teeth on the gear to match original and snap into the bearing. Insert the connecting rod into the long shaft gear and then push back into the short shaft gear. The video said to remove the drawer front but I did not and don't see that it necessary.

Customer service provided a video of the ice maker removal and installation. I watched the video and performed the remove and replacement.
Simple task.
Shout out to the customer service person, OUTSTANDING SERVICE. I apologize for not getting her name, great job.

Replaced the solenoid that feeds the icemaker. Easy fix remove the trays on the right and remove rear panels on the inside of the refrigerator. Pop the inlet solenoid replace it. Be sure to shut power and water OFF.

Switched the drain out using the video tutorial
Fixed the problem
Have had no more drain issues

Removed the shelf below the cover to allow plenty of room to work spread apart the old cover at the pivot point toward the back installed the new one in reverse order

Followed the instructions in the video provided via email from Partselect
However, the part received was the opposite design of the part removed.
It appeared this could be left hand right hand choice of part. Moreover, the button on the switch that turns the light off/on when door is open/closed was not functional due to the part being the opposite of the part I was replacing. I tested the switch I was replacing and it appears this is not the problem. I think the light socket is the problem. I am 69 year old female and capable of doing small repairs, but limited knowledge of electrical so having to troubleshoot by trial and error. Thank you.

replaced condensation tube with upgrade thawed freezer compartment so outlet hole was free of ice. that means pulling back compartment open to verify the hole is indeed free of ice. the ice maker on the other hand was freezing up solid, replaced solenoid config. as recommended by the tech. still same scenario. turned freezer temp up as far as it would go past recommended temp, which is 4 above zero F. still same results water cup that feeds the tray freezes solid then water runs all over a freezes until you cant get the tray out to work on it. moral to that story it didn't work.

The switch fix but did not fix the problem. I assumed the wires go on the same way as on the old switch. Is it possible if one light Burns out, the other will not work either?

Unsnapped and pulled off small cover exsposing two phillips head screws. I removed larger cover and styrofoam insert fully exsposing the damper unit. i unplugged same and with a 1/2 inch wood chisel was able to release the "snaps" holding the old unit in place. Simply reverse procedure to install new unit.

The installation video for condenser fan motor helped a lot to know how to disconnect the old fan motor and connect the new one. So easy just know how to remove and put back the fan gently, observe carefully where is the center and the connector position; 15 min after everything was done and the unit works well to date.

I received the wrong part - had to pay returnin shipped and restock fee. Lost out on dealing with this company. Went to Whirlpool site and got correct light for my refrigerator