Quick Question!

Have you ever purchased from PartSelect.com before?

Authentic Parts
Models > KEYS677EQ0 > Parts

KEYS677EQ0 KitchenAid Dryer - Parts

All parts for the KitchenAid Dryer KEYS677EQ0

Below is a list of all parts for the KitchenAid Dryer KEYS677EQ0. To find the repair part you need, you can browse the list below or you can narrow your choices by searching for a part by name or description.

All Parts for the KEYS677EQ0
< PREV 1 2 3 4 5 6 ... 11
1-14 of 146
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$8.98
In Stock

Thermal Fuse

This thermal fuse is designed for use in dryers. It is a safety mechanism that stops the flow of electricity to the heating element when a dryer overheats. When this fuse is faulty...

$14.56
In Stock

Multi Rib Belt - 92-1/4"

This multi rib belt is an important part in your dryer, it is what helps rotate the drum. The belt attaches to the drum, idler pulley, and motor pulley. As the armature of the motor rotates, the belt begins to move and turns the drum. If you notice the drum of your dryer is not spinning during the dry cycle, but you hear the motor running, your belt may have snapped and it will need to be replaced. This belt features four ribs and three grooves, however it replaces a wide variety of belts including wider styles that had five ribs and four grooves. When installing this part make sure the grooves are facing down, against the drum. This replacement part is 92 1/4 inches in length, and 1/4 inch wide. Before you begin any repair work, make sure your dryer has been unplugged.

$61.75
In Stock

Heating Element - 240V 5400W

The heating element is strung with a coiled wire that is made out of a nickel and chrome alloy. The function of the coiled wire on the heating element is to receive and resist a co...

$14.81
In Stock

Door Switch - 3 Wire

A door switch is a simple on/off switch mechanism that prohibits the dryer from operating when the door is open. This part may need to be replaced if you find that the dryer is not starting, will not shut off or the door will not close properly. All you will need is a putty knife and a Phillips screwdriver. Pry open the top of the dryer, remove the two screws underneath the lint collector without removing the entire thing, unplug the switch, remove the screws that hold the switch place, take out the old switch and install the new one by screwing it back into place.

$14.96
In Stock

Thermostat, Internal-Bias

A cycling thermostat is in tune with the temperature of your dryer and regulates it in order to maintain a certain temperature. This thermostat reaches a temperature of 155 degrees...

$3.56
In Stock

Door Catch Kit

This is a door catch kit, and it is designed for use with your dryer. On your appliance you will find both a strike and a catch, these two parts work together to keep your dryer door closed. This kit includes two strikes, three catches, and a set of instructions. Each of the door catches included have a different tension. Make sure you use the one that matches the existing catch on your appliance. All three of these are color-coded, and have a number on the back. The instruction sheet will tell you which catch you need to use for your specific model type.

$35.86
In Stock

Thermal Cut-Off Kit

The thermal cut off turns off the heating component when the dryer overheats, ensuring there is a consistent level of heat at all times. This dryer thermal cut-off kit includes one...

$10.34
In Stock

Drum Support Roller

This is a drum support roller for a dryer. The part includes the drum roller only and does not include the tri rings. Although most dryers require two drum support rollers, this part is sold separately. It is recommended to check and replace both drum support rollers at the same time to ensure proper drum rotation and because they often wear at the same rate. The drum support roller holds the drum in the proper position while it spins on the support wheels. If rollers are worn out, they will cause the dryer to be noisy. This is a genuine replacement part.

$10.04
In Stock

Idler Pulley Assembly

This part provides the tension required for a multi-ribbed belt. It also serves to help the belt to rotate the drum and attaches to the idler pulley wheel. If your dryer will not s...

$5.76
In Stock

Tri Ring

If you notice that your dryer is noisy or will not tumble, you may need to replace the tri ring. This part is triangular, and is less than an inch in size. Tri rings can be found both on the idler pulley shaft, or on the rear drum roller shaft. In either case, you will need to remove the front panel of the dryer and the drum to access the part for repair. Once you have accessed the damaged tri ring, you will simply need to slip it off and replace it with the new one. This part is sold individually. Be sure to disconnect the power source from the dryer before you begin this repair.

$4.94
In Stock

Heating Element Connection Wire Kit

This kit is used for electric clothes dryers, and it comes with a yellow wire nut.

$29.91
In Stock

Lint Filter

This dryer lint screen comes with a handle. This filter collects lint as it passes through the dryer vent.

$5.84
In Stock

Leveling Foot

If your washer shakes or vibrates loudly when it reaches its max speed, check that the leveling legs are even. To ensure that the washer is firmly on the ground using all four legs...

$9.74
In Stock

Light Bulb - 10W

This ten watt appliance light bulb is two inches tall. It is used with both washers and dryers.

All Parts for the KEYS677EQ0
< PREV 1 2 3 4 5 6 ... 11
1-14 of 146

All brand logos are trademarks of their respective owners.

The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.

Copyright © 1999-2017 , Eldis Group Partnership. All rights reserved.