KESH307GBT1 KitchenAid Range - Instructions

Ordered the part. when it arrived-quite speedily, I just unpacked it and put the cotton gasket around the glass and screwed it to the proper place in the oven. Very easy.

The repair went very well the most difficult was getting the door off. There is a certain way to do it as the springs in the door are very strong. It went well except for a small cut a thumb. The repair is easier with two people at least to get the door removed. You must be very careful to remember how the door comes apart. Be careful to not touch the glass putting it in once it is installed it is impossible to get the finger prints off. With help of a friend or in this case my son along with a couple of bloody marys it went well and we had fun.

thanks

took out the old dome cover and replaced it with a new one by unscrewing and replaced the new one and a fiberglass gasket. simple.

removed 4 scews underside of door 2 more at top to remove door handle. than removed front door panel. removed inner sheild by bending 4 tabs.removed outside door glass than insideglass. reversed process to complete.

With glass side down:
1. Removed the side panels
2. Removed the bottom panel
Turned over door holding glass in place.
3. Removed outer glass panel
4. Removed handle top
5. Removed top screw holding hinge mechanism
6. Removed screw for spacer and clip holding hinge mechanism
7. Lifted hinge mechanism out and replaced with new part.
Reattached parts and screws in reverse order (6-1)

Pulled the oven door out. Took the whole door apart and put it back together. The first time I put it back together the inner glass was still loose so I had to take it apart again and figure out how to hold everything together tightly. Your part was perfect. The glass was exactly the same as two others in the oven door. I wish I had instructions but when the parts fit it sure helps.

Easy.
Remove 2 screws.
Remove wires from old element.
Attach wires to new element.
Replace screws.
Took 5 minutes.

I think this does not qualify as a repair. I called and ordered the oven rack, it came in the mail and I put it in the oven. Nothing to it.

took the door off, removed the screws, removed the back of the door, took the broken glass out, put new glass in, reassemble door, put door back on.

Removed door parts & cleaned each, till the glass was reached. Replaced glass and reinstalled parts in order removed.

The first time I took the door apart to see what part to order it was difficult. The second time I knew what I was in for and was more prepared. Replacing the hinges were no problem. It was taking apart the door that was more difficult.

Replaced the oven light with a new one but it burnt out as soon as I turned it on. Therefore I decided a new socket may help.

My whirlpool apparently has the old style socket which is pictured in partselect part #PS12584564. The old style socket has to two metal arms that retain it against the metal reflector.

The part that will come (#PS12584564) however is the new style that whirlpool has changed to, apparently. It is not as pictured. The socket and the reflector have different retention devices.

I used screw drivers to bend the two metal arms away to release the socket. Then I had to use allen wrenches to bend the reflector's retention tabs away.

Once I had the old socket, reflector, and lens replaced I just followed the video on partselect for part #PS12584564

This worked very well, thanks to the advice posted from other users. The only part that was a bit unclear was removing the door. There are small, slotted metal pieces screwed into the sides of the oven to hold the door hinges in the slots. After removing those, I had to hold the door and push it up and down, and a little bit side to side, to get the hinges to start sliding out, but they did. There are no other screws or brackets holding them in place. The hinges are on springs, so they do snap up when they come out of the slots in the sides of the oven. But they only snap to a 90 degree angle, so they won't cut your fingers off. You'd have to hold your fingers right on them to even get pinched. After that, I just kept taking screws out of the door until I got through to the back panel, replaced it, and put it all back together.

Watched video and followed the very accurate and helpful instructions. A #2 Phillips screwdriver was the only tool required. This is an easy job for the average person.

It was alittle difficult at 1st to remove the clips that held in the socket. But once out everything went smoothly.