All Installation Instructions for Kelvinator Range KEF355ASA

Heavy jam boiler caused elements to sag

Removed the old & simply inserted the new one

Parts Used:

Surface Element - 8 Inch - 2600W

Danny L from CHELAN, WA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

The right Drawer Glide was broken.

The simplest repair ever! I just snapped it in and put the drawer back - fixed. I hope I have other repairs this simple.

Parts Used:

Rear Drawer Glide

Fred from Gregory, MI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

The switch wasn't working on all the different settings.

first thing was to turn the breakers off. then pull the range away from the wall. used an 1/8 th inch socket to take off the back panel to get access to the switch.used a Phillips screwdriver to disconnect the switch under the knob in the front. took off the wire terminals one at a time and matched it to the numbers on the old switch.replaced the knob, screwed it on to the range. turned the breakers on and tested the switch.worked fine, replaced the back cover and pushed it back into place.

Parts Used:

Infinite Burner Switch - Large Element

James from NEW HYDE PARK, NY
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Broken drawer slide

Remove drawer. Insert new slide. Install drawer.

Parts Used:

Front Drawer Glide

Michael from Jacksboro, TN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Broken right side parts for lower over storage drawer.

Sat on floor, pulled drawer out, inserted new clips, remounted door, stood up, high-fives myself.

Parts Used:

Rear Drawer Glide

Front Drawer Glide

Ty from Baltimore, MD
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

lens was broken

after pulling away from wall and unplugging remove 5 screws in upper back panel lift off being careful of sharp edges if part of lens is still in hole push it out towards the front insert lens from front of unit slide light assy over pin on back of lens replace back panel plug in range push back against wall check for level you're done

Parts Used:

Indicator Light Lens

Kenneth from Coeur d'Alene, ID
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Lacking oven racks on used appliance

Your website is great...easy and it literally took me no mote than 5 minutes to find what I needed and order...and received it VERY quickly. Must say I was dreading going to some parts house that we have in our town in bad area, and searching on dusty shelves for what I needed...am so glad I found you!!

Parts Used:

Oven Rack

Katherine from Roanoke, VA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

over draw was off track

the part snapped on the side of the track, now the draw is not sitting on the floor and opens and closes like new.

Parts Used:

Front Drawer Glide

Frances from Hauppauge, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Large front burner would not come on under setting of "3"

Replaced infinite control very easily.

Parts Used:

Infinite Burner Switch - Large Element

Steven from Edina, MN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers

3 of 7 people found this instruction helpful.

Was this instruction helpful to you?

dead burner

I unplugged the dead burner and plugged in the new burner. Very easy. No tools needed.

Parts Used:

Surface Element - 8 Inch - 2600W

Jan from Storm Lake, IA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 7 people found this instruction helpful.

Was this instruction helpful to you?

burner was damaged

snap out the old one and snap in the new

Parts Used:

Surface Element - 8 Inch - 2600W

Thomas from Elizabeth City, NC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

broken element

I followed instructions on your video. Took 10 minutes. My wife thought I was a pro.

Parts Used:

Bake Element - 240V

Peter from LEWISTON, ME
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

guide was broken

Used a slot screwdriver to pry the old guide...clipped the new guide into its place.

Parts Used:

Front Drawer Glide

Marvin from MONTANA CITY, MT
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Terminal block was bad.

Cut the old block off tied new wires to hot wires . That easy!

Parts Used:

Terminal Block Kit

Chuck from EVANSVILLE, IN
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Burner element failed

Plugged the new one in and it worked.
I did search out Frigidaire parts and there are other types tha may or may not work. Calrod burners are not all that unusual. I went with the real thing.

Parts Used: